Answer:
FOLLOWED BY... 2 6 5 3 5 8 9
UwU
the importance of reading a circuit diagram to interpret a wiring diagram?
Answer:
The ability to read electrical schematics is a really useful skill to have. To start developing your schematic reading abilities, it's important to memorize the most common schematic symbols. ... You should also be able to get a rough idea of how the circuit works, just by looking at the schematic.
Explanation:
Electronic components are often mounted with good heat conduction paths to a finned aluminum base plate, which is exposed to a stream of cooling air from a fan. The sum of the mass times specific heat products for a base plate and components is 5000 J/K, and the effective heat transfer coefficient times surface area product is 10 W/K. The initial temperature of the plate and the cooling air temperature are
Answer:
Hello your question is incomplete below is the complete question
Electronic components are often mounted with good heat conduction paths to a finned aluminum base plate, which is exposed to a stream of cooling air from a fan. The sum of the mass times specific heat products for a base plate and components is 5000 J/K, and the effective heat transfer coefficient times surface area product is 10 W/K. The initial temperature of the plate and the cooling air temperature are 295 K when 300 W of power are switched on. 1) Find the plate temperature after 10 minutes.
answer ; 311.36 k
Explanation:
Given data :
sum of mass * specific heat products for a base plate and components ( Mcp )
= 5000 J/K
effective heat transfer coefficient * surface area ( hA ) = 10 W/K
Initial temperature of plate and cooling air temperature( Tc ) = 295 k
power ( Q = W ) = 300 W
a) Determine plate temperature after 10 minutes
10 mins = 600 secs ( t )
heat supplied = change in temp + heat loss
Q * t = mCp ( ΔT ) + hA ( ΔT ) t
300*600 = 5000 * ( T -295 ) + 10 ( T -295 ) * 600
therefore ; T - 295 = 16.363
T = 311.36 K
Technician A says that an A-pillar may be designed to transfer collision energy
Technician B says that a floor pan reinforcement may be designed to transfer collision energy
Who is right?
A. Aonly
B. B only
C. Both A and B
D. Neither Anor B
Technicians A and B both are right with respect to their thinking and determination. Thus, the correct option is C.
What is Collision energy?Collision energy may be defined as a circumstance in which two or more bodies or particles come together with a resulting exchange of energy and alteration of direction.
Both pillar and floor pan reinforcement may be designed to transfer collision energy through the most prominent way to explain this mechanism of collisions.
A pillar exerts complete pressure on the floor in order to support the roof of the building, while floor pan reinforcement performs the same mechanism of collision energy with a different mechanism of action.
Therefore, technicians A and B both are right with respect to their thinking and determination. Thus, the correct option is C.
To learn more about Collisions energy, refer to the link:
https://brainly.com/question/2356330
#SPJ2
2. What is the main job of a cylinder head?
OA. Contain the rapid increase in combustion chamber temperature
OB. Contain the rapid increase in combustion chamber pressure
OC. Prevent engine oil from getting past the pistons
OD. Hold the Head Gasket in place
Grade/Exit
Answer:
Explanation:
The cylinder head sits on the engine and closes off the combustion chamber. The gap that remains between the cylinder head and the engine is completed by the head gasket. Another task of the cylinder head is to ensure the constant lubrication of the cylinder
These are sites that allow you to upload and download media content such as images, audio, and video
trevor moves a magnetic toy train away from a magnet that cannot move. what happens to the potential energy in the system of magnets during the movement?
Answer:a
Ieieksdjd snsnsnsnsksks
Think about all the things that you have learned about wildfire in this module.
In light of climate change, explain how this risk map might look different in 100 years.
Answer:
CLIMATE CHANGE HAS inexorably stacked the deck in favor of bigger and more intense fires across the American West over the past few decades, science has incontrovertibly shown. Increasing heat, changing rain and snow patterns, shifts in plant communities, and other climate-related changes have vastly increased the likelihood that fires will start more often and burn more intensely and widely than they have in the past.
Explanation:
What did Congress do in 1787 to settle land disputes among the settlers?
Answer:
On July 13, 1787, Congress enacts the Northwest Ordinance, structuring settlement of the Northwest Territory and creating a policy for the addition of new states to the nation. ... In 1781, Virginia began by ceding its extensive land claims to Congress, a move that made other states more comfortable in doing the same
Answer:
They divided up the Northwest Territory into acre squares and sold them.
Explanation:
According to O*NET, what is the most common level of education among Licensing Examiners and Inspectors?
You've asked an Incomplete question, lacking options. I answered based on the existing O*NET report.
Answer:
high school diploma
Explanation:
According to the Occupational Information Network (O*NET), most people who are Licensing Examiners and Inspectors typically have a high school diploma.
In other words, they do not seek to acquire a post-secondary school education.
Answer:
B
Explanation:
According to edge its answer B
associate's degree or on-the-job experience
got it right as a lucky guess as the O*net site is updated but edge doesn't bother to update their questions or links.
Click this link to view O*NET’s Education section for Licensing Examiners and Inspectors. According to O*NET, what is the most common level of education among Licensing Examiners and Inspectors?
bachelor’s degree
associate's degree or on-the-job experience .......This is the correct answer.
some college, no degree
associate degree
calculate the quantities of materials required for the first class brickwork in 1:6 cement mortar for 10 cu.m. assume the suitable data.
entor" by
What type of signal word is used in this sentence?
need and
en who was
generalization
description
thought
feeling
Answer:
generalization
Explanation:
Please mark me brainliest I need to level up
A power washer is being used to clean the siding of a house. Water enters at 20 C, 1 atm, with a velocity of 0.2 m/s .A jet of water exits at 20 C, 1 atm, with a velocity of 20 m/s an elevation of 5 m. At steady state, the magnitude of the heat transfer rate from the power unit to the surroundings is 10% of the power input. Determine the power input to the motor, kW.
A power washer is being used to clean the siding of a house. Water at the rate of 0.1 kg/s enters at 20°c and 1 atm, with the velocity 0.2m/s. The jet of water exits at 23°c, 1 atm with a velocity 20m/s at an elevation of 5m. At steady state, the magnitude of the heat transfer rate from power unit to the surroundings is 10% of the power input. Determine the power input to the motor in kW.
Answer:
Net power of 1.2 KW is being extracted
Explanation:
We are given;
Mass flow rate; m' = 0.1kg/s
Inlet temperature; T1 = 20°C = 293K
Inlet pressure; P1 = 1 atm = 10^(5) pa
Inlet velocity; v1 = 0.2 m/s
Exit Pressure; P2 = 1 atm = 10^(5) pa
Exit Temperature; T2 = 1 atm = 296K
Exit velocity; V2 = 20m/s
Change in elevation; h = Z2 - Z1 = 5m
We are told that the magnitude of the heat transfer rate from the power unit to the surroundings is 10% of the power input.
Thus;
Q = -0.1W
From Bernoulli equation;
Q - W = ∆Potential energy + ∆Kinetic energy + ∆Pressure energy
Where;
∆Potential energy = mg(z2 - z1)
∆Kinetic energy = ½m(v2² - v1²)
∆Pressure energy = mc_p(T2 - T1)
Thus;
-0.1W - W = [m'g(z2 - z1)] + [½m'(v2² - v1²)] + [m'c_p(T2 - T1)]
Where C_p is specific heat capacity of water = 4200 J/Kg.k
Plugging in the relevant values, we have;
-1.1W = (0.1 × 9.81 × 5) + (½ × 0.1(20² - 0.2²)) + (0.1 × 4200 × (296 - 293))
-1.1W = 4.905 + 19.998 + 1260
-1.1W = 1284.903
W = -1284.903/1.1
W ≈ -1168 J/s ≈ -1.2 KW
The negative sign means that work is extracted from the system.
A heat pump is to be used to heat a house during the winter, as shown in Fig. 6–52. The house is to be maintained at 21 ℃ at all times. The house is estimated to be losing heat at a rate of 135,000 kJ/h when the outside temperature drops to -5 ℃. Determine the minimum power required to drive this heat pump.
Answer:
[tex]3.32\ \text{kW}[/tex]
Explanation:
[tex]T_c[/tex] = Outside temperature = [tex]-5^{\circ}\text{C}[/tex]
[tex]T_h[/tex] = Temperature of room = [tex]21^{\circ}\text{C}[/tex]
[tex]Q_h[/tex] = Heat loss = 135000 kJ/h = [tex]\dfrac{135000}{3600}=37.5\ \text{kW}[/tex]
Coefficient of performance of heat pump
[tex]\text{COP}=\dfrac{1}{1-\dfrac{T_c}{T_h}}\\\Rightarrow \text{COP}=\dfrac{1}{1-\dfrac{273.15-5}{273.15+21}}\\\Rightarrow \text{COP}=11.3[/tex]
Input power
[tex]W_i=\dfrac{Q_h}{\text{COP}}\\\Rightarrow W_i=\dfrac{37.5}{11.3}\\\Rightarrow W_i=3.32\ \text{kW}[/tex]
The minimum power required to drive this heat pump is [tex]3.32\ \text{kW}[/tex].
Un material determinado tiene un espesor de 30 cm y una conductividad térmica (K) de 0,04 w/m°C. En un instante dado la distribución de temperatura en función de "x" el cual es la distancia desde la cara izquierda de una pared, está dado por la siguiente función: T(x) = 150x2 -30x, donde x está en metros. Calcúlese el flujo de calor por unidad de área cuando x=0 y x=30, para cada caso menciones si se está enfriando o calentando el sólido.
Answer:
Para x=0:
[tex]\phi=1.2 W/m^{2}[/tex]
Para x=30 cm:
[tex]\phi=-2.4 W/m^{2}[/tex]
Explanation
Podemos utilizar la ley de Fourier par determinar el flujo de calor:
[tex]\phi=-k\frac{dT}{dx}[/tex](1)
Por lo tanto debemos encontrar la derivada de T(x) con respecto a x primero.
Usando la ley de potencia para la derivda, tenemos:
[tex]\frac{dT(x)}{dx}=300x-30[/tex]
Remplezando esta derivada en (1):
[tex]\phi=-0.04(300x-30)[/tex]
Para x=0:
[tex]\phi=0.04(30)[/tex]
[tex]\phi=1.2 W/m^{2}[/tex]
Para x=30 cm:
[tex]\phi=-0.04(300*0.3-30)[/tex]
[tex]\phi=-2.4 W/m^{2}[/tex]
Espero que te haya ayudado!
I need help with part (C). Pleasee help me. It’s due in a few hours.
Answer:
u do the same thing as part B but only add 100 k, I think, cuz I'm still in middle school but I mean if u see it asks u to do the same thing as B but C says that instead, u do it at half pressure and 100 k is higher temp so what its asking is to repeat b but the twist is u do it at half pressure and 100 k is the higher temp
hope this helps :)
The quantity of bricks required increases with the surface area of the wall, but the thickness of a masonry wall does not affect the total quantity of bricks used in the wall
True or False
Answer:
false
Explanation:
advantage of iron meter
Answer:
Less Friction Error
Explanation:
The friction error is very less in the moving
iron instrument because their torque weight
ratio is high.
hope it helps!
Answer:
Universal Use -The MI instrument is independent of the of current and hence for both AC and DC
Explanation:
Mark as Brainlist Answer
A battery with an f.e.m. of 12 V and negligible internal resistance is connected to a resistor of 545 How much energy is dissipated by the resistor in 65 s?
Answer:
When are resistors in series? Resistors are in series whenever the flow of charge, called the current, must flow through devices sequentially. For example, if current flows through a person holding a screwdriver and into the Earth, then
R
1
in Figure 1(a) could be the resistance of the screwdriver’s shaft,
R
2
the resistance of its handle,
R
3
the person’s body resistance, and
R
4
the resistance of her shoes.
Figure 2 shows resistors in series connected to a voltage source. It seems reasonable that the total resistance is the sum of the individual resistances, considering that the current has to pass through each resistor in sequence. (This fact would be an advantage to a person wishing to avoid an electrical shock, who could reduce the current by wearing high-resistance rubber-soled shoes. It could be a disadvantage if one of the resistances were a faulty high-resistance cord to an appliance that would reduce the operating current.)
Two electrical circuits are compared. The first one has three resistors, R sub one, R sub two, and R sub three, connected in series with a voltage source V to form a closed circuit. The first circuit is equivalent to the second circuit, which has a single resistor R sub s connected to a voltage source V. Both circuits carry a current I, which starts from the positive end of the voltage source and moves in a clockwise direction around the circuit.
Figure 2. Three resistors connected in series to a battery (left) and the equivalent single or series resistance (right).
To verify that resistances in series do indeed add, let us consider the loss of electrical power, called a voltage drop, in each resistor in Figure 2.
According to Ohm’s law, the voltage drop,
V
, across a resistor when a current flows through it is calculated using the equation
V
=
I
R
, where
I
equals the current in amps (A) and
R
is the resistance in ohms
(
Ω
)
. Another way to think of this is that
V
is the voltage necessary to make a current
I
flow through a resistance
R
.
So the voltage drop across
R
1
is
V
1
=
I
R
1
, that across
R
2
is
V
2
=
I
R
2
, and that across
R
3
is
V
3
=
I
R
3
. The sum of these voltages equals the voltage output of the source; that is,
V
=
V
1
+
V
2
+
V
3
.
This equation is based on the conservation of energy and conservation of charge. Electrical potential energy can be described by the equation
P
E
=
q
V
, where
q
is the electric charge and
V
is the voltage. Thus the energy supplied by the source is
q
V
, while that dissipated by the resistors is
q
V
1
+
q
V
2
+
q
V
3
.
Explanation:
Which of the following is a basic type of weld? O Groove O Lap O Edge O Corner
What is the primer coating that protects the metal from rusting on a Aftermarket part.. Flat Primer
Primer Sealer
Shipping Primer
Air at 1 atm and 25◦C blows across a large concrete surface 20 m wide maintained
at 60◦C. The flow velocity is 6 m/s. Calculate the convection heat loss from the
surface.
This is heat transfer convection, mechanical engineering
please solve this question guys I'm gonna really really be appreciate it for you guys
Answer:
Air at 1 atm and 25◦C blows across a large concrete surface 20 m wide maintained
at 60◦C. The flow velocity is 6 m/s. Calculate the convection heat loss from the
surface.
This is heat transfer convection, mechanical engineering
please solve this question guys I'm gonna really really be appreciate it for you guys
How many kg moles of Sodium Sulphate will contain 10 kg of
Sodium?
70.40mol cuz
1g sodium sulfate = 0.00704mol
take 10kg × 1000 = 10,000g
10,000g × 0.00704
final answer 70.40mol
(as per my thinking)
Answer:
70.40mol cuz
1g sodium sulfate = 0.00704mol
take 10kg × 1000 = 10,000g
10,000g × 0.00704
final answer 70.40mol
If a poems has a regular rhythm throughout the poem, it has: PLEASE HELP MEH I WILL GIVE YOU BRAINLEIST!!
A. tone
B. imagery
C. irony
D. meter
Answer:
D, meter.
Explanation:
Rhythm is associated with meter, which identifies units of stressed and unstressed syllables.
If a poem has a regular rhythm throughout the poem, it has a meter. Option D is correct.
What is meter in poem?Meter, which distinguishes between stressed and unstressed syllables, is related to rhythm. The fundamental rhythmic framework of a stanza or a line of poetry is known as meter.
The number of feet in the poem serves as a measure of the poem's meter, which is the rhythm of the language.
Many traditional poem forms call for a certain verse meter or a group of meters that alternate in a specified pattern. Prosody refers to both the study of meters and other types of versification, as well as their practical application.
Therefore, option D is correct.
To learn more about the poem, refer to:
https://brainly.com/question/12155529
#SPJ6
The reversible and adiabatic process of a substance in a compressor begins with enthalpy equal to 1,350 kJ/kg, and ends with enthalpy equal to 3,412 kJ/kg. If the compressor efficiency is 0.85, find the actual specific work required by the compressor to operate, in kJ/kg.
Answer:
the actual specific work required by the compressor to operate is 2425.88 kJ/kg
Explanation:
Given that;
h₁ = 1350 kJ/kg
h₂₅ = 3412 kJ/kg
compressor efficiency П_ise = 0.85
we know that;
compressor efficiency П_ise = isentropic work / actual work
П_ise = (h₂₅ - h₁) / (h₂ - h₁ )
so
0.85 = (h₂₅ - h₁) / (actual work )
Actual work = (h₂₅ - h₁) / 0.85
Actual work = (3412 - 1350) / 0.85
Actual work = 2062 / 0.85
Actual work = 2425.88 kJ/kg
Therefore the actual specific work required by the compressor to operate is 2425.88 kJ/kg
What type of engineer makes sure equipment is safe and operational
Answer:
mechanical engineer is the best answer
What is the name given to the vehicles that warn motorists about oversized loads/vehicles?
a) Pilot Car
b) Advanced Car
c) Trail Car
d) Leader Car
The car that is used to warn drivers about oversized loads is the Pilot Car.
What is a Pilot Car?The Pilot Car is also called Escort Car. It is a vehicle used to warn other vehicles of the presence of an over-sized vehicle.
The role of Pilot vehicle operators is to warn road users (motorists) to be cautious of over-sized loads or vehicles.
The cars are used to guide motorists that are making use of roads in construction sites.
Read more on driving: https://brainly.com/question/4533625
Waste that is generated by a business is called a _____________.
A) Waste stream
B) Surplus
C) Hazard assessment
D) Trash stream
(This is for my Automotive class)
Answer:
waste stream
Explanation:
i got it right on sp2
A converging nozzle has an exit area of 0.001 m2. Air enters the nozzle with negligible velocity at a pressure of 1 MPa and a temperature of 360 K. For isentropic flow of an ideal gas with k = 1.4 and the gas constant R = Ru/MW = 287 J/kg-K, determine the mass flow rate in kg/s and the exit Mach number for back pressures of (a) 500 kPa and (b) 784 kPa.
Answer:
a) for back pressures of (a) 500 kPa
- mass flow rate is 2.127 kg/s
- exit Mach number is 1.046
b) for back pressures of (a) 784 kPa
- mass flow rate is 1.793 kg/s
- exit Mach number is 0.6
Explanation:
Given that;
A₂ = 0.001 m²
P₁ = 1 MPa
T₁ = 360 K
k = 1.4
P₂ = 500 Kpa
(1000/500)^(1.4-1 / 1.4) = 360 /T₂
2^(0.4/1.4) = 360/T₂
1.219 = 360 / T₂
T₂ = 360 / 1.219
T₂ = 295.32 K
CpT₁ + V₁²/2000 = CpT₂ + V₂²/2000
we substitute
CpT₁ + V₁²/2000 = CpT₂ + V₂²/2000
1.005 × 360 = 1.005 × 295.32 + v₂²/2000
v₂ = 360.56 m/s²
p₂v₂ = mRT₂
500 × (0.001 × 360.56) = m × 0.287 × 295.32
m = 2.127 kg/s
so Mach Number = V₂ / Vc
Vc = √( kRT) = √( 1.4 × 287 × 295.32) = 344.47 m/s
So Mach Number = V₂ / Vc = 360.56 / 344.47 = 1.046
Therefore for back pressures of (a) 500 kPa
- mass flow rate is 2.127 kg/s
- exit Mach number is 1.046
b)
AT P₂ = 784 kPa
(1000/784)^(1.4-1 / 1.4) = 360/T₂
T₂ = 335.82 K
now
V₂²/2000 = 1.005( 360 - 335.82)
V₂ = 220.45 m/s
P₂V₂ = mRT₂
784 × (0.001 × 220.45) = m( 0.287) ( 335.82)
172.83 = 96.38 m
m = 172.83 / 96.38
m = 1.793 kg/s
just like in a)
Vc = √( kRT) = √( 1.4 × 287 × 335.82) = 367.32 m/s
Mach Number = V₂ / Vc = 220.45 / 367.32 = 0.6
Therefore for back pressures of (a) 784 kPa
- mass flow rate is 1.793 kg/s
- exit Mach number is 0.6
Following are the
Given:
[tex]A_2 = 0.001\ m^2\\\\P_1 = 1\ MPa\\\\T_1 = 360\ K\\\\k = 1.4\\\\P_2 = 500\ Kpa\\\\[/tex]
To find:
Flow rate of mass, and Mach number
Solution:
For point a)
Using formula:
[tex]\to P^{\frac{r-1}{r}} \alpha T\\\\\to (\frac{1000}{500})^(\frac{1.4-1}{1.4}) = \frac{360}{T_2}\\\\\to 2^(\frac{0.4}{1.4}) = \frac{360}{T_2}\\\\\to 1.219 = \frac{360}{T_2}\\\\\to T_2 = \frac{360}{1.219}\\\\\to T_2 = 295.32\ K\\\\[/tex]
[tex]\to C_pT_1 + \frac{V_1^2}{2000} = C_pT_2 + \frac{V_2^2}{2000}\\\\\to 1.005 \times 360 = 1.005 \times 295.32 + \frac{v_2^2}{2000}\\\\\to v_2 = 360.56 \ \frac{m}{s^2} \\\\\to p_2v_2 = mRT_2\\\\\to 500 \times (0.001 \times 360.56) = m \times 0.287 \times 295.32\\\\\to m = 2.127\ \frac{kg}{s}\\\\[/tex]
Mach Number [tex]= \frac{V_2}{V_c}\\\\[/tex]
[tex]\to V_c = \sqrt{( kRT)} = \sqrt{( 1.4 \times 287 \times 295.32)} = 344.47 \ \frac{m}{s}\\\\[/tex]
[tex]\to \frac{V_2}{V_c} = \frac{360.56}{344.47} = 1.046[/tex]
For point b)
[tex]\to P_2 = 784\ kPa\\\\\to (\frac{1000}{784})^{(\frac{0.4}{1.4})} = \frac{360}{T_2}\\\\\to T_2 = 335.82\ K\\\\[/tex]
now
[tex]\to \frac{V_2^2}{2000} = 1.005( 360 - 335.82)\\\\\to V_2 = 220.45 \frac{m}{s}\\\\\to V_c = \sqrt{( kRT)} = \sqrt{( 1.4 \times 287 \times 335.82)} = 367.32\ \frac{ m}{s}\\\\\to c= \frac{220.45}{ 367.32} = 0.6\\[/tex]
Learn more about flow rate of mass, and Mach number:
brainly.com/question/15055873
Consider a condenser in which steam at a specified temperature is condensed by rejecting heat to the cooling water. If the heat transfer rate in the condenser and the temperature rise of the cooling water is known, explain how the rate of condensation of the steam and the mass flow rate of the cooling water can be determined. Also, explain how the total thermal resistance R of this condenser can be evaluated in this case.
Answer:
Q = [ mCp ( ΔT) ] [tex]_{cooling water }[/tex]
(ΔT)[tex]_{cooling water}[/tex] and Q is given
[tex]m_{cooling water}[/tex] = [tex]\frac{Q}{Cp[ T_{out} - T_{in} ] }[/tex]
next the rate of condensation of the steam
Q = [ m[tex]h_{fg}[/tex] ][tex]_{steam}[/tex]
[tex]m_{steam} = \frac{Q}{h_{fg} }[/tex]
Total resistance of the condenser is
R = [tex]\frac{Q}{change in T_{cooling water } }[/tex]
Explanation:
How will the rate of condensation of the steam and the mass flow rate of the cooling water can be determined
Q = [ mCp ( ΔT) ] [tex]_{cooling water }[/tex]
(ΔT)[tex]_{cooling water}[/tex] and Q is given
[tex]m_{cooling water}[/tex] = [tex]\frac{Q}{Cp[ T_{out} - T_{in} ] }[/tex]
next the rate of condensation of the steam
Q = [ m[tex]h_{fg}[/tex] ][tex]_{steam}[/tex]
[tex]m_{steam} = \frac{Q}{h_{fg} }[/tex]
Total resistance of the condenser is
R = [tex]\frac{Q}{change in T_{cooling water } }[/tex]
A product (that has not been yet invented) that involves lighting up when something happens?
Answer:
Maybe when there is a fire there can be fire drones that can take it out. and it can also resuce people who are stuck there.
Explanation: