A noisy transmission channel has a per-digit error probability p = 0.01.
(a) Calculate the probability of more than one error in 10 received digits?

To determine the required insulation thickness, you will need to use the heat transfer equation, which states that the rate of heat transfer through a material is equal to the product of the heat transfer coefficient, the surface area of the material, and the temperature difference between the two sides of the material.

The temperature difference between the chilled water and the ambient air is 30°C - 8°C = 22°C.

The surface area of the pipe is given by the formula for the surface area of a cylinder:

A = 2πrL

where:

r = the radius of the pipe

L = the length of the pipe.

The radius of the pipe is 5 cm / 2 = 2.5 cm = 0.025 m.

The surface area of the pipe is therefore A = 2π(0.025 m)(150 m) = 7.85 m²

The heat transfer rate through the insulation is given by: Q = (kA)(ΔT)/d, where:

Q= the heat transfer rate,

k = the thermal conductivity of the insulation,

A = the surface area of the pipe,

ΔT = the temperature difference between the chilled water and the ambient air,

d = the thickness of the insulation.

Rearranging this equation to solve for d, the thickness of the insulation, we get:

d = (0.05 W/m·°C)(7.85 m²)/(9 W/m²·°C)(22°C) = 0.03 m = 3 cm.

Therefore, the required thickness of the insulation is 3 cm.

Learn more about heat energy: https://brainly.com/question/25384702

#SPJ4

In order to determine the absolute maximum shear stress developed in a beam, you will need to know the following information:

The beam's cross-sectional area: The amount of material that can withstand shear forces will be determined by this.

The shear stress that a beam can withstand before failing will depend on its material qualities.

The beam is being sheared by this force: The amount of shear stress that develops in the beam will depend on this.

The length of the beam will affect how much it deforms when a shear force is applied.

Using this knowledge, you can apply the calculation below to determine the absolute maximum shear stress that has been created in the beam:

Shear force / cross-sectional area equals shear stress.

Remember that the shear force is assumed to be distributed equally over the cross-section of the beam in this formula. The shear stress distribution across the beam may require a more involved analysis if the shear force is not distributed uniformly.

To know more about Shear Stress kindly visit
https://brainly.com/question/12910262

#SPJ4

(a) It will take about 4.8e-5 seconds for the surface to reach a safe-to-touch temperature of 42 °C.

(b) The corresponding temperature at the plastic/wood interface will be 200 °C, since this is the initial temperature and the interface is assumed to be adiabatic.

To solve this problem, we need to use the heat equation, which describes how heat flows through a material:

∂T/∂t = α ∂²T/∂x²

where T is the temperature, t is time, x is position, and α is the thermal diffusivity.

To solve this equation, we need to know the boundary conditions and initial conditions. In this case, the boundary conditions are the surface temperature (42 °C) and the temperature at the plastic/wood interface (200 °C). The initial condition is the initial temperature distribution, which is uniform at 200 °C.

First, let's find the convective heat transfer coefficient, k, using the relationship:

h = k / d

where d is the thickness of the plastic coating and k is the thermal conductivity.

Substituting the values given in the problem, we find that

k = 0.05 W/m-K.

Now, let's solve the heat equation using these values. To do this, we need to rearrange the equation to solve for t:

∂T/∂t = α ∂^2T/∂x^2

∂t = (α ∂^2T/∂x^2) / ∂T

t = ∫ (α ∂^2T/∂x^2) / ∂T dx

We can simplify this equation by assuming that the temperature change across the thickness of the plastic coating is small, so that ∂^2T/∂x^2 can be approximated as T''/d^2. Substituting this and the values for the other parameters gives us:

t = ∫ (α T''/d^2) / ∂T dx

= ∫ (α / k) dx

= (α / k) x

To find the time it takes for the surface to reach a safe-to-touch temperature of 42 °C, we need to solve for the time it takes for the temperature at the surface to drop from 200 °C to 42 °C. Substituting these values and the values for the other parameters gives us:

t = (1.2e-7 m2/s / 0.05 W/m-K) (2 mm)

= 4.8e-5 s

Learn more about heat energy: https://brainly.com/question/25384702

#SPJ4

Enthalpy Changes the overall energy change in the substance portrayed in the graph at  48°C.

Mass (m) = 0.3 Kg

Initial temperature (T1) = 20°C

Heat (Q) added = 35 KJ

Specific heat capacity (C) = 4.18 KJ/Kg°C

Final temperature (T2)

The final temperature of water can be obtained as follow:

Q = MC(T2 – T1)

35 = 0.3 x 4.18 (T2 – 20)

35 = 1.254 (T2 – 20)

Clear the bracket

35 = 1.254T2 – 25.08

Collect like terms

1254T2 = 35 + 25.08

1.254T2 = 60.08

Divide both side by the coefficient of T2 i.e 1.254

T2 = 60.08/1.254

T2 = 47.9 ≈ 48°C

Therefore, the final temperature of the water is 48°C.

Learn more about temperature on:

https://brainly.com/question/11464844

#SPJ1

As a result, induced voltage will drop as the coil's turn count is reduced. This phenomena is explained by Faraday's Law.

According to Faraday's Law, if a conductor is a part of a closed circuit, an electric current will flow whether the conductor is passed through a magnetic field or the magnetic field is moved past the conductor.

We are aware that if a static conductor is placed within a fluctuating magnetic field or if a conductor moves within a static magnetic field, a voltage will be induced. This phenomena is explained by Faraday's Law.

Changes to the magnetic field's strength, the conductor's movement in and out of the field, the distance between a magnet and the conductor, or the size of a loop in the field can all result in this shift.

Know more about loop here:

https://brainly.com/question/14390367

#SPJ4

Attach the modem and router. Hooking up and turning on devices in the right order is essential for setting up a network successfully. Start by connecting the modem to the wall using a coax wire (or a phone cable for DSL modems). Start the router first, then the modem. Cable from the wall to the modem must be connected.

To Learn more About modem and router refer To:

https://brainly.com/question/6358145

#SPJ1

The Fourier transform of each signal :

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is a[n-2] - a[n-6], so we can rewrite this as x[n] = a[n]e^2ω - a[n]e^6ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(a[n]e^2ω - a[n]e^6ω) e^-jnω

= ∑a[n]e^2ωe^-jnω - ∑a[n]e^6ωe^-jnω

= A(ω)e^2ω - A(ω)e^6ω

Therefore, the Fourier transform of x[n] = a[n-2] - a[n-6] is X(ω) = A(ω)e^2ω - A(ω)e^6ω.

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is -u[-n-1], so we can rewrite this as x[n] = -u[n+1]e^-j(n+1)ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(-u[n+1]e^-j(n+1)ω) e^-jnω

= -∑u[n+1]e^-jω

= -A(ω)e^-jω

Therefore, the Fourier transform of x[n] = -u[-n-1] is X(ω) = -A(ω)e^-jω.

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is 2*sin(n)u[-n], so we can rewrite this as x[n] = 2*sin(n)e^-jnω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(2*sin(n)e^-jnω) e^-jnω

= 2∑sin(n)e^-jnω

= 2A(ω)sin(ω)

Therefore, the Fourier transform of x[n] = 2*sin(n)u[-n] is X(ω) = 2A(ω)sin(ω).

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is (cos(n-1)), so we can rewrite this as x[n] = cos(n-1)e^-j(n-1)ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(cos(n-1)e^-j(n-1)ω) e^-jnω

= ∑cos(n-1)e^-jω

= A(ω)cos(ω-1)

Therefore, the Fourier transform of x[n] = (cos(n-1)) is X(ω) = A(ω)cos(ω-1).

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is sin(n) + cos(n), so we can rewrite this as x[n] = sin(n)e^-jnω + cos(n)e^-jnω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(sin(n)e^-jnω + cos(n)e^-jnω) e^-jnω

= ∑sin(n)e^-jnω + ∑cos(n)e^-jnω

= A(ω) (sin(ω) + cos(ω))

Therefore, the Fourier transform of x[n] = sin(n) + cos(n) is X(ω) = A(ω) (sin(ω) + cos(ω)).

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is sin(n) + cos(n), so we can rewrite this as x[n] = sin(n)e^-jnω + cos(n)e^-jnω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(sin(n)e^-jnω + cos(n)e^-jnω) e^-jnω

= ∑sin(n)e^-jnω + ∑cos(n)e^-jnω

= A(ω) (sin(ω) + cos(ω))

Therefore, the Fourier transform of x[n] = sin(n) + cos(n) is X(ω) = A(ω) (sin(ω) + cos(ω)).

The Fourier transform of a signal x[n] is given by X(ω) = ∑x[n]e^-jnω. In this case, the signal x[n] is x[n-6] + x[n+6], so we can rewrite this as x[n] = x[n]e^-6ω + x[n]e^6ω. We can then use the Fourier transform formula to find the Fourier transform of the signal:

X(ω) = ∑(x[n]e^-6ω + x[n]e^6ω) e^-jnω

= ∑x[n]e^-6ωe^-jnω + ∑x[n]e^6ωe^-jnω

= A(ω) (e^6ω + e^-6ω)

Therefore, the Fourier transform of x[n] = x[n-6] + x[n+6]

Learn more about Fourier transform:

https://brainly.com/question/28984681

#SPJ4

Depending on whether Hi is greater than or equal to MD, the ALU either subtracts the MD register (the divisor) from its Hi input or allows the Hi input to pass through unaltered.

In conclusion, the division and multiplication operations used in this project are performed by the Arithmetic Logic Unit (ALU), which is an arithmetic and logical operation.

two binary values can be multiplied using this procedure. Take into account the fact that the ALU only offers the addition and shifting operations, not the multiplication operation. The microprogramming code can then be stored in memory and used to perform multiplication operations.

To know more about Arithmetic Logic Unit visit :-

https://brainly.com/question/28548014

#SPJ4

The variable that is used for flow control services is Buffer window .

For output in a console window, a screen buffer is a two-dimensional array of character and colour data. There may be several screen buffers on a console. The screen buffer that is visible is the current screen buffer. Every time a new console is created, the system builds a screen buffer.

A memory area known as a buffer is used to store data momentarily while it is being transferred from one location to another. When transferring data between computer processes, a buffer is employed. The vast majority of buffers are used in software.

To learn more about Buffer window refer to :

https://brainly.com/question/9906723

#SPJ1

This FedEx error indicates that the selected FedEx service is not allowed for the shipment's destination country. To resolve this error, select a different carrier service. View the FedEx services available with ShippingEasy.

You may send items up to 150 lbs., 108" in length, and 165" in length with girth using FedEx Ground® and FedEx Home Delivery® Services. If the shipment weights more than 75 lbs, place yellow and black safety heavyweight labels over the diagonal corners. Only when instructed to do so by the sender or by FedEx policy must you sign for a shipment. You can check the tracking details that were sent to you via email from the sender or input the package's tracking number on fedex.com to find out whether your shipment needs a signature.

To learn more about FedEx error click the link below:

brainly.com/question/29376073

#SPJ4

One of these important innovative advances is the use of electric switches to control electricity. Rotary Switch is the name of a certain type of rotary switch that moves in a circular motion and controls the circuit. Thus, option C is correct.

Switches. The most frequent way to control electrical circuits is through switches. By opening or closing the circuit, switches control a circuit. Manual, hydraulic, electrical, and pneumatic methods can all be used to operate switches.

Therefore, Fully automated machines require a Continuous-cycle reciprocation circuit.

Learn more about automated machines here:

https://brainly.com/question/24198010

#SPJ1

Deformed steering wheel Of The Following Would Most Likely Occur As The Direct Result Of The Second Collision. Air bubbles in the arterial blood vessels.

The second collision is the “human collision.” At the moment of impact, passengers in the car that are unrestrained are still travelling at the vehicle's original speed.

Stage 2: Human Collison During the second stage of “human collision,” all occupants in the vehicle will still be moving in the same direction and speed as they were before the collision happened. Inertia will keep the occupants moving toward the point of an impact unless a seatbelt or airbag stops them.

To know more about Second Collision visit :-

https://brainly.com/question/1871060

#SPJ4

Code for calculating the median, geometric mean, arithmetic mean, adaptive local noise reduction, and adaptive median filters. Your software receives a 2d matrix as input:

// Median

function median(matrix) {

 // sort array

 const sorted = matrix.sort((a, b) => a - b);

 const mid = Math.floor(sorted.length / 2);

 const isEven = sorted.length % 2 === 0;

 if (isEven) {

   return (sorted[mid - 1] + sorted[mid]) / 2;

 }

 return sorted[mid];

}

// Arithmetic Mean

function arithmeticMean(matrix) {

 return matrix.reduce((a, b) => a + b, 0) / matrix.length;

}

// Geometric Mean

function geometricMean(matrix) {

 return Math.pow(

   matrix.reduce((a, b) => a * b, 1),

   1 / matrix.length

 );

}

// Adaptive Local Noise Reduction

function adaptiveLocalNoiseReduction(matrix) {

 const result = [];

 const windowSize = 3;

 for (let i = 0; i < matrix.length; i++) {

   for (let j = 0; j < matrix[i].length; j++) {

     const nums = [];

     for (let x = i - windowSize; x <= i + windowSize; x++) {

       for (let y = j - windowSize; y <= j + windowSize; y++) {

         const row = matrix[x] ? matrix[x][y] : 0;

         if (row) {

           nums.push(row);

         }

       }

     }

     result.push(median(nums));

   }

 }

 return result;

}

// Adaptive Median Filter

function adaptiveMedianFilter(matrix) {

 const result = [];

 const windowSize = 3;

 for (let i = 0; i < matrix.length; i++) {

   for (let j = 0; j < matrix[i].length; j++) {

     const nums = [];

     for (let x = i - windowSize; x <= i + windowSize; x++) {

       for (let y = j - windowSize; y <= j + windowSize; y++) {

         const row = matrix[x] ? matrix[x][y] : 0;

         if (row) {

           nums.push(row);

         }

       }

     }

     const medianValue = median(nums);

     const medianDiff = nums.map((x) => Math.abs(x - medianValue));

     const minDiff = Math.min(...medianDiff);

     const minIndex = medianDiff.indexOf(minDiff);

     result.push(nums[minIndex]);

   }

 }

 return result;

}

What is code?
Code is a set of instructions, written in a programming language, that tells a computer what to do. Code can be written to create software applications, websites, and mobile apps, among other things. Code is written using specific programming languages, such as C++, Java, Python, and HTML. Programmers use code to define how a program should work and to give the computer a set of instructions to execute. Code is the cornerstone of the digital world, and it is the basis for all computer-related tasks. Without code, computers would be unable to perform any task.

To learn more about code

https://brainly.com/question/23275071

#SPJ4

GANs have proven helpful for semi-supervised learning, fully supervised learning, and reinforcement learning despite being initially presented as a type of generative model for unsupervised learning.

In June 2014, Ian Goodfella and his colleagues created a family of machine learning frameworks known as generative adversarial networks (GANs). One neural network gains at the expense of the other in a zero-sum game between two neural networks.

This method learns to produce fresh data with the same statistics as the training set given a training set. For instance, a GAN trained on images can produce new images with numerous realistic features that, at least on the surface, appear to be created by humans. GANs have proven helpful for semi-supervised learning, fully supervised learning, and reinforcement learning, while being initially presented as a type of generative model for unsupervised learning.

Know more about GANs here:

https://brainly.com/question/30072351

#SPJ4

The complete question is:

Unsupervised representation learning with deep convolutional generative adversarial networks. is the meaning of?

To replace the force system shown in Prob. 4-135 with a wrench, you will need to determine the magnitude and direction of the force and couple moment that the wrench should exert.

You can do this by taking the following actions:

Identify the net force influencing the system: You can accomplish this by adding up the various forces that are at work on the system. The net force in this situation is 200 + 400 = 600 N.

The system's net couple moment can be calculated by: This is accomplished by adding the two moments of the various forces at the wrench's x-z plane intersection. The net couple moment in this scenario is calculated as (0.5 m)(200 N) - (4 m)(200 N) - (3 m)(400 N) = -600 N*m.

Calculate the wrench's pair moment and force, taking into account their magnitude and direction: The equations for the force and couple moment of a wrench can be used for this.

To know more about Wrench kindly visit
https://brainly.com/question/10186385

#SPJ4

The statement that would be true about a critical path is; "All the Above" (Option D)

A critical path is the sequence of activities in a project that must be completed on time in order for the project to be completed on schedule. It is the longest path through the project, from start to finish, and includes the activities that have the least amount of scheduling flexibility. These activities are considered "critical" because any delay in their completion will directly impact the overall completion date of the project.

The critical path is important because it helps project managers identify the most important tasks in the project and allocate resources accordingly.

Learn more about Critical path:
https://brainly.com/question/16519233
#SPJ1

To determine the expiration date of the last annual aircraft inspection, a person should refer to the aircraft maintenance records.

What are aircraft maintenance records?

Aircraft maintenance records include information about the work done to the aircraft, the date it was finished, the signature of the maintenance team, information about the FAA certificate, and the certificate number and signature of the person who put the aircraft back in service. The maintenance records mentioned in this rule can be simplified into two groups: permanent records and expiring records.

Permanent records are those maintenance logs that need to be retained and kept up-to-date for the aircraft forever. They act as a record of every maintenance action that has taken place during the lifecycle of the aircraft. It also functions as a tool for figuring out whether an aircraft has received all necessary maintenance and is in a state that allows for safe flight.

To learn more about aircraft maintenance records, use the link given
https://brainly.com/question/27961960
#SPJ4

To find the acceleration of point A, we can use Newton's second law of motion, which states that the force acting on an object is equal to the mass of the object times its acceleration.

The total force acting on the rod is the force P at point A and the weight of the rod at point B. The weight of the rod is equal to its mass times the acceleration due to gravity, so the total force is:

F_total = P + m_rod * g

Where m_rod is the mass of the rod and g is the acceleration due to gravity.

The acceleration of point A is then:

a = F_total / m_rod

To find the location of the point on the bar that has zero acceleration, we can use the concept of center of mass.

For a uniform rod, the center of mass is located at the midpoint of the rod.

The linear density of the rod is equal to its mass divided by its length, so the length of the rod is:

L = F_total / (m_rod / L)

Solving for L in terms of the given quantities, we find that the length of the rod is:

L = (P + m_rod * g) / (m_rod / L)

This equation can be rearranged and solved to find the value of L.

L^2 = (P + m_rod * g) / (m_rod / L)

L^3 = P + m_rod * g

L^3 - m_rod * g = P

L = (P / (m_rod * g))^(1/3)

Substituting in the given values, we find that:

L = ((0.25 lb) / (1.85 lb * 32.2 ft/s^2))^(1/3) = 0.45 ft

So the length of the rod is 0.45 ft and the location of point B is 0.45 ft from point A.

Here the calculation to find that the midpoint of the rod:

((0.25 lb) + (1.85 lb * 32.2 ft/s^2)) / (2 * (1.85 lb / L)) = 0.225 ft

So the point on the rod that has zero acceleration is located 0.225 ft from point A.

The missing part in the question is shown below.

A uniform slender rod AB rests on a frictionless horizontal surface, and a force P of magnitude 0.25 lb is applied at A in a direction perpendicular to the rod. Assume that the rod weighs 1.85 lb, dib, difermine  the acceleration of point  a) the acceleration of point A , (c) the location of the point B c) the location of the point on the bar that has zero acceleration.

Learn more about newton's law, here https://brainly.com/question/15280051

#SPJ4

Since all processes have a finish value of true, the safe sequence is P2, P3, P1. Therefore, the correct answer is (B) P1, P2, P3.

To find the safe sequence using the Banker's algorithm, you need to perform the following steps:

Using these steps, we can find the safe sequence for the given scenario as follows:

Need matrix:

P1: 3-2=1, 3-3=0, 3-3=0

P2: 2-1=1, 1-1=0, 0-0=0

P3: 1-1=0, 1-1=0, 1-0=1

Work array: [2, 1, 1]

Finish array: [false, false, false]

Step 1: Process P2 has a need of [1, 0, 0] which is less than or equal to the work array, so it can be allocated resources. Update work array to [2-1=1, 1-0=1, 1-0=1] and set finish[P2]=true.

Work array: [1, 1, 1]

Finish array: [false, true, false]

Step 2: Process P3 has a need of [0, 0, 1] which is less than or equal to the work array, so it can be allocated resources. Update work array to [1-0=1, 1-0=1, 1-1=0] and set finish[P3]=true.

Work array: [1, 1, 0]

Finish array: [false, true, true]

Step 3: Process P1 has a need of [1, 0, 0] which is less than or equal to the work array, so it can be allocated resources. Update work array to [1-1=0, 1-0=1, 0-0=0] and set finish[P1]=true.

Work array: [0, 1, 0]

Finish array: [true, true, true]

Thus, the right answer is (B) P1, P2, P3.

Learn more about algorithm, here https://brainly.com/question/22984934

#SPJ4

Using the knowledge of computational language in python it is possible to write a code that first line contains an integern, the number of students.

#include<bits/stdc++.h>

using namespace std;

const int Mx=1e5+5;

int par[Mx],cnt[Mx];

void ini(int n){

   for(int i=1;i<=n;++i)par[i]=i,cnt[i]=1;

}

int root(int a){

   if(a==par[a])return a;

   return par[a]=root(par[a]);

}

void Union(int a,int b){

   a=root(a);b=root(b);

   if(a==b)return;

   if(cnt[a]>cnt[b])swap(a,b);

   par[a]=b;

   cnt[b]+=cnt[a];

}

int* getTheGroups(int n,int q,int sz,string queryTypes[],int student1[],int student2[],int* ans){

   ini(n);

   int current=0;

   for(int i=0;i<q;++i){

       if(queryTypes[i]=="Friend"){

           Union(student1[i],student2[i]);

       }

       else{

           int x=root(student1[i]),y=root(student2[i]);

           if(x==y)ans[current++]=cnt[x];

           else ans[current++]=cnt[x]+cnt[y];

       }

   }

   return ans;

}

int main(){

   int n,q,sz=0;

   cin>>n>>q;

   string queryTypes[q];

   int student1[q],student2[q];

   for(int i=0;i<q;++i){

       cin>>queryTypes[i];

       if(queryTypes[i]=="Total")

           ++sz;

   }

   cin>>q;

   for(int i=0;i<q;++i)cin>>student1[i];

   cin>>q;

   for(int i=0;i<q;++i)cin>>student2[i];

   int ans[sz];

   int* ptr=getTheGroups(n,q,sz,queryTypes,student1,student2,ans);

   for(int i=0;i<sz;++i)

       cout<<ptr[i]<<endl;

   return 0;

}

See more about python at brainly.com/question/18502436

#SPJ1

The sentences that best describe ISO 9001:2015 are:

1) Quality management systems- requirements

2) ISO 9001 is certifiable by accredited certification bodies

3) "Combination of internal and external issues that can have an effect on an organization's approach to developing and achieving its objectives" is the definition of: Context of the organization

4) "Systematic, independent and documented process for obtaining objective evidence and evaluating it objectively to determine the extent to which the audit criteria are fulfilled" is the definition of: Audit

5) Mandatory documented information required by ISO 9001:2015 standard includes: Scope of the quality management system, Quality objectives, Design and development changes, and Maintenance of infrastructure

6) The clause of ISO 9001:2015 standard which is the requirement for conducting internal audit specified is Clause 9: Performance evaluation

7) Audit criteria include: ISO 9001:2015 standard, Customer contract requirements, Quality manual, and Operating procedures

8) Internal audit shall be performed at planned intervals by internal auditors of the organization implementing ISO 9001:2015 quality management system.

9) Purpose of conducting internal audits includes checking compliance of the quality management system against ISO 9001:2015 requirements, identifying improvement needs, and evaluating the effectiveness of the quality management system.

10) Extent and boundaries of an audit are defined as: Audit scope

11) The principles of auditing include: Ethical conduct, Evidence based approach, Due professional care

12) As long as a piece of critical monitoring equipment is periodically used by the operators who know how to use it skillfully, a formalized maintenance and calibration program is not necessary: False

ISO 9001:2015 determines requirements for a quality management system provided an organization needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements and aims to enhance customer satisfaction through the effective application of the system

Therefore, the correct answer is as given above

learn more about ISO 9001:2015: https://brainly.com/question/28870416

#SPJ1

Structured Query Language (SQL), Query by Example (QBE) are tools used to run queries in an rdbms.

What is rdbms?
RDBMS (Relational Database Management System) is a type of database management system that stores data in tabular form, allowing for complex queries and records to be accessed quickly and easily. RDBMSs are used to store large amounts of data and can be used by a variety of different applications. RDBMS is based on the relational model, which uses a key-value pair structure to store data. This structure allows data to be related to each other, enabling the user to easily query and manipulate the data. RDBMSs also provide features like security, data integrity, scalability and performance. RDBMSs are widely used in applications like e-commerce, healthcare, banking and finance. They are also used in data warehouses, data marts and analytics applications.

To learn more about rdbms
https://brainly.com/question/24225134
#SPJ4

Complete Question:
a query is a request for information stored in a database. one of the benefits of using a database to store information is the ability to run a query. in relational database management systems (rdbms), there are a variety of query tools that are used to execute and run queries. which of the following are tools used to run queries in an rdbms?

A. Structured Query Language (SQL)

B. Database Query Language (DQL)

C. NoSQL

D. Query by Example (QBE)

Answer:

Difficulty getting a loan or credit card.

An increase in debt.

Difficulty keeping assets.

A loss of money.

Explanation:

The emphasis of today's job search is on the needs of the employer.

An employer plays a wide range of roles. Being up to date and fostering a work environment that promotes employee satisfaction means understanding what it means to be an employer today.

The definition of an employer is a person or a group operating in the public, private, nonprofit, or commercial spheres that employs and compensates workers. The employer, who holds the position of authority within an organisation, establishes the conditions of employment for workers and provides the negotiated terms, such as the salary.

A person who shapes an organization's culture is another way to describe an employer. Employers have the power to make a strong statement about the hierarchy within the workplace and how employees should interact with one another through their actions.

Learn more about Employers

https://brainly.com/question/26463698

#SPJ4

Note that a milling machine can do all of the following tasks except: " ream a highly accurate hole with a fine finish" (Option D).

A milling machine is a tool that is used to machine flat and contoured surfaces, and it can also be used to rotate a multitoothed cutter into the workpiece to remove material. It is also capable of machining threads, gears, and spirals.

However, a milling machine is not typically used to ream holes, as reaming is a finishing operation that is usually done with a reamer, which is a specialized tool designed for this purpose. Reaming is used to create highly accurate holes with a fine finish, and it is typically done after the hole has been drilled or milled to its rough size.

There are several advantages to using a milling machine, including:

Versatility: Milling machines can be used to machine a wide range of parts and materials, including flat and contoured surfaces, threads, gears, and spirals.

Precision: Milling machines are capable of producing highly precise parts, as they can be accurately positioned and controlled using computer numerical control (CNC) technology, etc.

Learn more about milling machines:
https://brainly.com/question/23275945
#SPJ1

The most common architectural element shared between Greek and Etruscan architecture is the use of rounded arches.

Rounded arches were used in both Greek and Etruscan architecture to create a sense of grandeur and grandiosity, as well as to support the weight of the structure. In Greek architecture, the use of arches was often seen in temples, colonnades, and other monumental structures, while in Etruscan architecture, arches were often used in tombs and other funerary structures.

Additionally, arches allowed for a greater degree of structural stability, as they were able to distribute weight better than straight walls or pillars. Furthermore, the use of rounded arches in both Greek and Etruscan architecture provided a stylistic unity, as the two cultures had many similarities in terms of their architectural styles.

For more questions like Rounded arches click the link below:

https://brainly.com/question/2826840

#SPJ4

Special shapes are used in flowcharts to depict various kinds of operations or steps in a process. The order of the steps and their interactions are depicted with lines and arrows. Symbols for flowcharts are those. Thus, option D is correct.

Data Flow – An arrow sign, which denotes the direction of flow, is used to represent the movement of data between external entities, procedures, and data stores.

Therefore, a data flow uses various symbols and shapes to represent data flow, processing, and storage.

Learn more about data flow here:

https://brainly.com/question/15517161

#SPJ1

The two functions of nested list will be:

[[Int]]

sumNestedList :: [[Int]] -> Int

sumNestedList xs = sum (map sum xs)

sumNestedList2 :: [[Int]] -> Int

sumNestedList2 = foldr (\x acc -> sum x + acc) 0

What is nested list?

A nested list is a list of lists, or a list that contains other lists as elements. It is an effective way to organize and store data in a hierarchical structure. Nested lists are useful for organizing data into categories and subcategories, such as products and their sub-components or ingredients. A nested list is also a way to represent a tree data structure, which is a type of hierarchical data structure that consists of nodes connected by directed edges. Nested lists can also be used to represent graphs, networks, and other complex data structures.

To learn more about nested list

https://brainly.com/question/15048204

#SPJ4