The energy in the system is given by the initial potential energy at the point 1.
The linear velocity at point 3, is approximately 33.59 m/s.
Reasons:
The parameters are;
Height at point 1, h₁ = 83 m
Radius of the ring = 8 cm
Mass of the ring, M = 8 kg
Height at point 2, h₂ = 32 m
At point 2, we have;
Change in potential energy = Kinetic energy
Which gives;
(83 - 32) × 9.81 × 8 = 0.5 × 8 × v² + 0.5 × 8 × 0.08² × (v/0.08)²
Which gives;
v ≈ 22.37 m/s
At point 3, the rotational kinetic energy remains constant while the
translational kinetic energy increases as follows;
K.E. at point 3 = Initial kinetic energy + Change in potential energy
Which gives;
K.E. at point 3 = 0.5 × 8 × v₃³ ≈ 0.5×8×22.37² + 32×9.81×8
[tex]v_3^2 = \dfrac{0.5 \times 8 \times 22.37^2 + 32 \times 9.81 \times 8}{0.5 \times 8} = 1128.15[/tex]
v₃ ≈ √(1128.15) ≈ 33.59
The linear velocity at point 3, v₃ ≈ 33.59 m/s
Learn more here:
https://brainly.com/question/15076457
The probable question parameters as obtained from a similar question online are;
Height at point 1, h₁ = 83 m
Radius of the ring = 8 cm
Mass of the ring, M = 8 kg
Height at point 2, h₂ = 32 m
what are saturated and non saturated vapour?
Answer:
A saturated vapour is one that is in balance with its own liquid. Space is considered to be unsaturated if it contains fewer vapours than the maximum amount it can retain at a given temperature. Saturated vapour pressure is unaffected by volume, although it rises as temperature rises.
Explanation:
A stone is dropped from the edge of a roof, and hits the ground with a velocity of -150 feet per second. How high (in feet) is the roof
Answer:
how long does it take? we need it to answer ure question
Explanation:
cause we don't know how many feet until we know how long it was falling
If a stone is dropped from the edge of a roof and hits the ground with a velocity of -150 feet per second, then the height of the roof would have been 1148 feet.
What are the three equations of motion?There are three equations of motion given by Newton
v = u + at
S = ut + 1/2 × a × t²
v² - u² = 2 × a × s
As given in the problem, a penny is dropped from a building that is 95 m tall, the initial velocity of the penny is zero, and the acceleration acting is due to the acceleration due to gravity,
By using the second equation of the motion for the vertical motion ,
v² = ( 2 × g ×h )
150² = 2 × 9.8 × h
h = 22500 / 19.6
= 1148 feet
Thus, the height of the roof would have been 1148 feet.
To learn more about equations of motion here, refer to the link given below ;
brainly.com/question/5955789
#SPJ2
Explain why a tiny 1.5 V cell can operate a calculator for a year, while a much larger 1.5 V cell burns out in a few hours in a tiny robot. I WILL CHOOSE BRAINIEST!! PLEASE HELP
The reason why a tiny 1.5 V cell can operate a calculator for a year, but would burn out in a few hours in a tiny robot is because the power demands of the calculator are way less than that of the tiny robot.
What controls how long a cell lasts ?Cell capacity is measured by the amount of Amps and Amp Hour (A.H.) capacity for how long a battery can endure.
On the label or in the user's manual, batteries mention their reserve capability, which specifies the approximate amount of time they can operate between charges. You might notice a shorter or longer battery life if your circuit uses more or less power than this hypothetical circuit. Calculate the battery's entire capacity and divide it by the power of your circuit to see how long it can survive.
Load current, which is influenced by the power of the linked item, influences how quickly the battery's electrical capacity will be used up.
The reason the 1.5 V cell would operate the calculator for a year and yet die in a few hours with the robot is that the robot has a much higher load current than the calculator.
Find out more on cell life at https://brainly.com/question/4503865
#SPJ1
Please help. I'm mot sure what I need to do first...
Answer:
0.80 kN
Explanation:
Hope you understood it
How many states of matter are there?
Answer:
3
Explanation:
state of matter are solid
liquid and
gases
1.25 is the closest to 1.04 or not I want to answer please. I think it's true, but I want to prove it scientifically, please.
Answer:
in general context yes it is closest to 1.04
Explanation:
theres no right or wrong way to scientifically prove this though.
Overall in scale its closest to 1.04 hope that helped
The elevation at the base of a ski hill is 350 m above sea level. A ski lift raises a skier (total mass=72 kg, including equipment) to the top of the hill. If the skier's gravitational potential energy relative to the base of the hill is now 9.2 x 105 J, what is the elevation at the top of the hill?
The elevation at the top of the hill is 1,653.85 m.
The given parameters;
initial height of the skier, h₁ = 350 mlet the final height of the skier at the hill top, = h₂total mass, m = 72 kggravitational potential energy of the skier, P.E = 9.2 x 10⁵ JThe elevation at the top of the hill is calculated as follows;
[tex]P.E = mg\Delta h\\\\P.E = mg(h_2 -h_1)\\\\h_2 -h_1 = \frac{P.E}{mg} \\\\h_2 = \frac{P.E}{mg} + h_1\\\\h_2 = \frac{9.2 \times 10^5 }{72 \times 9.8} \ + \ 350 \ m\\\\h_2 = 1,653.85 \ m[/tex]
Thus, the elevation at the top of the hill is 1,653.85 m.
Learn more here:https://brainly.com/question/24515193
At which type of boundary is new oceanic crust created?
A. a convergent plate boundary
B. a divergent plate boundary
C. a subduction plate boundary
D. a transform plate boundary
Answer:
c.
Explanation:
If the two plates that meet at a convergent plate boundary both are of oceanic crust, the older, denser plate will subduct beneath the less dense plate. The older plate subducts into a trench, resulting in earthquakes. Melting of mantle material creates volcanoes at the subduction zone.
When two oceanic plates converge, the denser plate will end up sinking below the less dense plate, leading to the formation of an oceanic subduction zone. Old, dense crust tends to be subducted back into the earth. An example of a subduction zone formed from a convergent boundary is the Chile-Peru trench….
Answer:
a divergent plate boundary
When does your body conduct current more readily?
when it is hot
when it is dry
when it is cold
when it is wet
Answer:
When you are wet or you are sweating current passes easily.
Explanation:
wetness increases conductivity. therefore 'when it is wet'.
When tightening a bolt, you push perpendicularly on a wrench with a force of 185 N at a distance of 0.11 m from the center of the bolt. How much torque are you exerting relative to the center of the bolt
Explanation:
The torque exerted on the wrench is
[tex]\tau = Fd\sin{\theta} = Fd[/tex]
since the force is applied perpendicular to the wrench, in which sin90 = 1. The torque then is
[tex]\tau = (185\:\text{N})(0.11\:\text{m}) = 20.35\:\text{N-m}[/tex]
. A load of 250 kg is hung by a crane’s cable. The load is pulled by a horizontal force such that the cable makes a 300 angle to the vertical plane. If the load is in the equilibrium, calculate the magnitude of the tension in the cable.
If the load is in the equilibrium, the magnitude of the tension in the cable is equal to 1,414.5 Newton.
Given the following data:
Mass of load = 250 kgAngle of inclination = 30°Scientific data:
Acceleration due to gravity = 9.8 [tex]m/s^2[/tex]To calculate the magnitude of the tension in the cable, if the load is in the equilibrium:
First of all, we would determine the tension caused by the horizontal component of the force:
[tex]\sum F_y ; Tcos\theta - mg=0\\\\Tcos\theta = mg\\\\T=\frac{mg}{cos\theta} \\\\T=\frac{250 \times 9.8}{cos30} \\\\T= \frac{2450}{0.8660}[/tex]
T = 2,829.1 Newton
The magnitude of the tension in the cable is given by:
[tex]\sum F_x ; F - Tsin\theta = 0\\\\F = Tsin\theta\\\\F = 2829.1sin30\\\\F = 2829.1 \times 0.5[/tex]
F = 1,414.5 Newton.
Read more on tension here: https://brainly.com/question/18792908
Jane plans to fly from Binghamton, New York, to Springfield, Massachusetts, about 280 km due east of Binghamton. She heads due east at 280 km/h for one hour but finds herself at Keene, which is 294 km from Binghamton in a direction 17.8 degrees north of due east. What was the wind velocity
Answer:
90m/h N
Explanation:
we consider janes velocity to the positive X axis so Vj=280km/s
and the final position a dot in on the graph r=294km, we find the x and y components:
294*cos(17.8)=280 X+ confirming our theory
294*sin(17.8)=90 Y+ or N and that's the winds' velocity.
The photo shows a skateboarder pushing her foot against the ground as she rides down a hill.
How does this action cause the skateboarder’s speed to change?
Answer:
A
Explanation:
Down the hill, the net force increases if she pushes more forward.
Answer:
its a im just did the test
Explanation:
identify the following prefixes:
1) Di-
2) Tetra-
3) Deca-
4) Hepta-
Explanation:
Di -. 2
Tetra. -3
deca. -. 10
Hepta. -- 7
help :”)
a skydiver jumps out of a plane and falls for 45 seconds before deploying his parachute. how far did he fall?
Answer:
200 feet
Explanation:
you are standing ata known distance from the statue of liberty describe how you could determine its height using only a meter stick
Use the meter stick to measure your height to the level of your eyes, then use trigonometry ratio formula to calculate the height from your eyes' level and above of the statue of liberty with angle of elevation, then, add the two heights.
If you are standing at a known distance from the statue of liberty, a meter stick can be used to measure your known distance away from the statue of liberty.
To determine its height using only a meter stick, the angle at which you look at the peak of statue of liberty must be measured or known. The height of the statue of liberty can be calculated if you know the angle of elevation at which you look at the peak of the statue, and the availability of the meter stick.
Use the meter stick to measure your height to the level of your eyes, then use trigonometry ratio formula to calculate the height from your eyes' level and above of the statue of liberty. That is,
Tan Ф = opposite / adjacent
Tan Ф = H/d
H = d x TanФ
Where
H = calculated height from the eyes level and above
Ф = angle of elevation
d = known distance away from the statue
Let h = Your measured height of your body to the eyes level
Then,
The height of the statue of liberty = H + h
Learn more here: https://brainly.com/question/24693484
The symbol or variable to used find initial velocity is
Answer:
v down exponenet 1 brainlest
Explanation:
Answer:
v0 [vee nought] is the initial velocity when time=0
3) A 60. kg person is in an elevator. The elevator starts from rest and then accelerates upwards at 2.0 m/s^2 for 4.0 seconds. Calculate the work done by the normal force on the person. *
Answer:
WD = 960 J
Explanation:
WD = work done (J)
F = force (N)
s = displacement (m)
m = mass (kg) = 60
a = acceleration (m/s²) = 2
t = time (s) = 4
u = initial velocity (m/s) = 0
The formulas or equations that are relevant ate:
WD = F × s
F = m × a
s = u + at
We want to find WD, so we need to now the force and the displacement (or distance);
We calculate force, in Newtons, with the formula F = ma:
F = 60 × 2
F = 120 N
We also need displacement, which get with the formula s = u + at:
s = 0 + 2(4)
s = 8 m
Now we have F and s, we can calculate WD:
WD = 120 × 8
WD = 960 J
Methodology:
Starting with what you want to find, in this case WD, list the formula/s you could use;
Then, identify the information you need for the formula and whether or not you are given that information;
Next, list the formulas for the information you don't have and once again, identify whether the information you are given is sufficient to use those formulas;
Once you can calculate all necessary information, then proceed to calculate the values and finally, the answer;
I suggest also keeping a list of all the variables as I've done at the top of my working so it is clear for you to see and use.
what does stimlus mean
Answer:
a thing or event that evokes a specific functional reaction in an organ or tissue.
or
a thing that rouses activity or energy in someone or something; a spur or incentive.
A Pump discharges water at 1MPaa and 165 deg C. Determine the specific volume and internal energy of the water at the discharge point.
This problem is describing a pump from which water is discharged at 1 MPa and 165 °C and is asking for the specific volume and internal energy at those conditions, thus, we can use the steam tables for resolving this requirement.
First of all, we need to remember that water can be a saturated liquid, vapour or liquid-vapour mixture, and this is determined for the temperature and pressure it is at.
In this case, we find that at 165 °C the saturation pressure is about 0.6178 MPa; this means we are referring to a saturated liquid so that both the specific volume and internal energy can be simply read from the steam tables as vf and uf as follows:
[tex]v=0.001127\frac{m^3}{kg}\\\\u=761.67 \frac{kJ}{kg}[/tex]
Learn more:
https://brainly.com/question/13177371https://brainly.com/question/15298076A ball is dropped from an 80.0 m building. What is the ball's velocity after 3.00 s? Use an order-of-magnitude estimation to identify the correct choice.
A. -2.9 m/s
B. -29.4 m/s
C -8.8 m/s
D. -88.3 m/s
Answer:b
Explanation:
-29.4 m/s
The velocity of the ball dropped from 80 m if it reaches the ground within 3 seconds is 26.6 m/s. If it is in midway within this time, then the velocity will be 29.4 m/s.
What is velocity ?Velocity of a moving object is the measure of its distance travelled per unit time. Velocity is a vector quantity having both magnitude and direction. Acceleration is the rate of change in velocity.
Given that, height of the building = 80 m
the ball is moving downwards by acceleration due to gravity g = 9.8 m/s².
Then after 3 seconds, the velocity of the ball is calculated as follows:
velocity = acceleration × time
v = 9.8 m/s² × 3 s = -29.4 m/s
If the ball reaches the ground within the time of 3 s, then, the velocity is:
v = 80 m/3s = 26.6 m/s.
Find more on velocity :
brainly.com/question/18084516
#SPJ6
The amount of work done in example B is:
Answer:
Explanation:
20 n is an unknown amount
If that is supposed to be 20 N(ewtons)
then W = Fd = 20(15) = 300 J
Answer: it will be 300 newton meters
Explanation:
The average normal body temperature measured in the mouth is 310 K. What would Celsius thermometers read for this temperature?
54.1°C
23.8°C
36.9°C
42.7°C
________
= 310 - 273
= 37°C
Actually,310 Kelvin is same with 37°C, and as you see, there is no 37°C
So, The Nearest Number To 37°C is 36,9°C
Answer:
36.9
Explanation:
Plato
Rachel drops a ball from a hot–air balloon while her friend Lisa is watching her from the ground. Which statement about the ball's motion is true from Lisa's point of view?
Assume that there is no air resistance and the hot–air balloon is moving horizontally.
A. The ball drops to the ground along a straight–line path.
B.When the ball lands, the hot–air balloon will be ahead of it.
C. When the ball lands, the hot–air balloon will be behind it.
D. When the ball lands, the hot–air balloon will be directly above it.
Answer:
According Lisa, both the ball and the balloon have the same forward velocity of Vx.
(D) is correct
100 J of work was done to lift a 10-N rock and set it at Position A near the edge of a cliff.
1. If the 100 Joules of work lifted the rock to the top of the cliff, how much potential energy did the rock gain?
2. At point C, the rock's potential energy will be
3. The rock's kinetic energy at point A is
4. At point B, some of the rock's potential energy will be changed to Kinetic energy
5. What is the mass of the rock?
6. What is the rock's velocity just before it hits the ground?
The rock to the right is sitting at the top of a ramp. I wonder how much work it required to get that rock up there.
Answer:
lol
Explanation:
5) You pull a 10.0 kg wagon along a flat road. You exert a force of 80.0 N at an angle of 30.0 degrees above the horizontal while you move the wagon 10.0 m forward. The coefficient of friction between the wagon and road is 0.500. Calculate the work down by you and the work done by friction.
Can someone solve by showing the steps?
This question involves the concepts of work done and the frictional force.
a. Work done by the person is "692.82 N".
b. Work done by the frictional force is "490.5 N".
a.
Work done by the person can be given by the following formula:
[tex]W=FdCos\theta[/tex]
where,
W = work done by the person = ?
F = Force applied by the person = 80 N
d = distance traveled = 10 m
θ = angle between force and motion = 30°
Therefore,
[tex]W=(80\ N)(10\ m)Cos30^o[/tex]
W = 692.82 N
b.
Work done by the frictional force is given by the following formula:
[tex]W_f=fd\\W_f=\mu mgd[/tex]
where,
[tex]W_f[/tex] = work done by the frictional force = ?
μ = coefficient of friction = 0.5
g = acceleration due to gravity = 9.81 m/s²
Therefore,
[tex]W_f=(0.5)(10\ kg)(9.81\ m/s^2)(10\ m)[/tex]
[tex]W_f=490.5\ N[/tex]
Learn more about frictional force here:
https://brainly.com/question/1714663?referrer=searchResults
The linear distance traveled by a wheel of radius 50cm after 99 complete revolutions is?
1)99m
2)210m
3)311
4)433
Answer:
3) 311 m
Explanation:
Circumference = 2πR = π m/rev
99 rev(π m/rev) = 99π m or about 311 meters
Read the sentence from the text. “They are as glossy as satin or sunlight reflecting off water!" What does the word glossy mean in the sentence? O A. pointed o B. shiny O C. small O D. strong
Answer:
b Shiny
Explanation:
Trust me it's right
The vertical position of the 100-kg block is adjusted by the screw activated wedge. Calculate the moment which must be applied to the handle of the screw to raise the block. The single thread screw has square threads with a mean diameter of 30 mm and advances 10 mm each complete turn. The coefficient of friction for the screw threads is 0.24, and the coefficient of friction for all the mating surfaces of the block and the wedge is 0.40. Neglect friction at the ball joint A
We have that for the Question "" it can be said that Calculate the moment which must be applied to the handle of the screw to raise the block is
M = 7.30 N.mFrom the question we are told
The vertical position of the 100-kg block is adjusted by the screw activated wedge. Calculate the moment which must be applied to the handle of the screw to raise the block. The single thread screw has square threads with a mean diameter of 30 mm and advances 10 mm each complete turn. The coefficient of friction for the screw threads is 0.24, and the coefficient of friction for all the mating surfaces of the block and the wedge is 0.40. Neglect friction at the ball joint A
Generally the equation for the Block is mathematically given as
[tex]\sum Fy=0[/tex]
[tex]981cos21.80 = R_2cos53.6\\\\R_2=1535N[/tex]
the equation for the Wedge is mathematically given as
[tex]\sum Fx=0\\\\1535cos36.4=Pcos21.8\\\\P=1331N[/tex]
the equation for the Screw is mathematically given as
[tex]\beta = tan^{-1}*\frac{L}{2*\pi*r} \\\\\beta = tan^{-1}*\frac{10}{2*\pi*(15)} \\\\\\beta = 6.06\\\\\theta = tan^{-1}*0.25 \\\\\theta = 14.04\\\\\\Therefore\\\\\theta + \beta = 20.1\\\\[/tex]
Therefore
[tex]M = Pr tan (\theta + \beta)\\\\M = 1331(0.015) tan20.09\\\\M = 7.30 N.m[/tex]
For more information on this visit
https://brainly.com/question/23379286
Objects 1 and 2 attract each other with a gravitational force of 12 units. If the mass of Object 2 is tripled, then the new gravitational force will be _____ units.
Explanation:
Fgravity = G*(mass1*mass2)/D².
G is the gravitational constant, which has the same value throughout our universe.
D is the distance between the objects.
so, if you triple one of the masses, what does that do to our equation ?
Fgravitynew = G*(3*mass1*mass2)/D²
due to the commutative property of multiplication
Fgravitynew = 3* G*(mass1*mass2)/D² = 3* Fgravity
so, the right answer is 3×12 = 36 units.