as the length of a muscle increases from its resting length of 100mm to 150mm which of the following changes in force occur? passive force increases and active force decreases passive force increases and active force increases passive force decreases and active force decreases passive force decreases and active force increases

The current in a circuit if the voltage applied to a load is 492 volts is 5.52 A.

Current is the rate of flow of electric charge around an electrical circuit. It is measured in amperes (A). Current can be calculated by dividing the voltage (V) by the resistance (R) of a circuit, according to the formula I = V/R.

Calculate the total resistance of the two series-connected resistive heating elements:

R = (250 V) / (2.8 kW) = 89.29 Ω

Calculate the current in the circuit using Ohm's Law:

I = (V) / (R) = (492 V) / (89.29 Ω) = 5.52 A

For more questions like Current click the link below:

https://brainly.com/question/27499791

#SPJ4

The minimum accelerating potential difference (magnitude) that would be required will be 62 kV.

Charged particles, such protons or electrons, are accelerated by particle accelerators to almost the speed of light. They then strike a target or additional particles with those fragments. According to Albert Einstein's special theory of relativity, the relativity of time prevents electrons from going faster than the speed of light when deciding whether they can do so.

Given, wavelength (λ) = 0.0220 nm = 0.22×10∧-10 m = 0.22 A°

λ = hc/eV

V = 12400/λ

V = 12400/0.22

V = 62000 V

V = 62 kV

The minimum accelerating potential difference (magnitude) that would be required to produce kV will be 62 kV.

To know more about electrons visit

brainly.com/question/1255220

#SPJ4

The complete question is,

An electron is accelerated toward a target. Find the minimum accelerating potential difference (magnitude) that would be required to produce kV. Assume the electron is initially at rest before accelerating toward the target.) wavelength of 0.0220 nm when the electron strikes the target. (Enter your answer in an x-ray with a kV.

If we know the stall torque and no load speed of a pm dc motor, the maximum power motor can deliver is P max = 1/2* Tstall * 1/2* ω(no load).

A mechanical device that produces stall torque has an output rotational speed of zero. Electric motors are capable of developing torque when stalled.

However, as the current flowing is at its maximum while an electric motor is halted, they are vulnerable to overheating and potential damage.

The no load speed is the speed when running at nominal voltage and zero load.

So, the maximum power motor can deliver is P max = 1/2* Tstall * 1/2* ω(no load).

To know more about power:

https://brainly.com/question/28528630

#SPJ4

The change in gravitational potential energy stored in 16 Jule.

Gravitational potential

In classical mechanics, of the  gravitational potential at in a  location is equal to the work per unit mass that's would be needed to Move an object to that locations from a fixed references  location. It is analogous to the electric potential with the mass playing the role of charge.

Sol-As per the given question ∆PE = mgh

M= skg

g= 4m/s^2

∆h = 2m

∆PE = 2m×4m×2m

= 16 Joules.

To know more about gravitational potential energy click-

https://brainly.com/question/15896499

#SPJ1

Positive acceleration describes an increase in speed; negative acceleration describes a decrease in speed. Hence option C is correct.

Acceleration is defined as the speed at which an object's velocity changes over time. It is a vector quantity to accelerate. If a point or object travelling straight forward accelerates or decelerates, it is moving faster or slower.  The equation a = v/t denotes acceleration (a), which is the change in velocity (v) over the change in time (t).

When the car accelerates positively, its speed rises. As the car slows down, its speed decreases. Negative acceleration occurs when a force causes a body's velocity to decrease. Therefore, the body's negative acceleration can also be referred to as its deceleration.

Thus, positive acceleration describes an increase in speed; negative acceleration describes a decrease in speed. Hence option C is correct.

To learn more about acceleration, refer to the link below:

https://brainly.com/question/12550364

#SPJ1

To sterilise a 50.0-g glass infant bottle, we must increase its heat from 22.0 to 95.0 degrees Celsius, or 3066 J of heat is transferred.

Heat is the result of the movement of kinetic energy within a material or an item, or from form of energy to a material or an object. Electromagnetic energy can be transported using three different mechanisms: radiation, conduction, and convection. Conduction of heat through solids, convection of liquids and gases, and electromagnetic radiation (radiation).

When a substance is subjected to a material-specific phase-change temperature, the material immediately undergoes a phase shift from a solid to a liquid. sources include solar energy, heat pumps, deep geothermal heat pumps, nat gas, lpg (LP), oil, coal, and wood.

50.0 g (0.84 J/g C) of heat was transported (95 C - 22 C)

= 3066 J of heat transferred

To know more about heat visit:

https://brainly.com/question/28921175

#SPJ4

The gravitational force exerted on a 50 kg mass on Jupiter's surface is 1.30×[tex]10^{3[/tex] N. Acceleration due to gravity on Jupiter is 2.23 times that of the earth.

Gravitational force is due to mass in an object. This is an attractional force with which all objects are attracting each other. All heavenly bodies have great mass. They attract each other and also if an object is reaching in their gravitational pull.

Force of gravity is calculated using the formula

F = G m1. m2/ [tex]r^{2}[/tex]

We are given mass of Jupiter and radius in terms of earth mass and radius.

volume of earth = 4/3 π[tex]r^{3[/tex]

Volume of Jupiter= 1323 × volume of earth

4/3 π[tex]R^{3[/tex] = 4/3 π[tex]r^{3[/tex] × 1323

R = r [tex]\sqrt[3]{1323}[/tex] =10.97 r

So, Gravity force on Jupiter = G 50 × 318 M/10.97 ×10.97[tex]r^{2}[/tex]

                                             =  50 ×5.97×[tex]10^{24[/tex]÷ 10.97×10.97×6.37×[tex]10^{6[/tex]

after calculation we get the value 1.30×[tex]10^{3[/tex] N

To know more about gravitational force here

brainly.com/question/12528243

#SPJ4

The type of observation that astronomers can use to measure the composition of extrasolar planet atmospheres : comparisons of a star's spectrum when planet is in transit versus when it is eclipsed.

Several planets outside the Solar System called exoplanets have been observed to have atmospheres. At the present , most atmosphere detections are of hot Jupiter or Neptune that orbit very close to their star and therefore have heated and extended atmospheres.

As a transiting extrasolar planet passes in front of its host star, one can observe the exoplanet's atmosphere as it is backlit by the star. Additional atmospheric observations can also be made by watching as exoplanet disappears and reappears from behind the star.

To know more about extrasolar planets, refer

https://brainly.com/question/14018668

#SPJ4

The change or mutation in a segment of DNA after replication may lead to changes in the genotype, the traits of the organism and the proteins (option i, ii and iii).

A genetic mutation is any change in the nucleotide bases of the genome of an organism that may be associated with modifications in the phenotypic traits or features of the organism if this change alters the expression of a given gene that produces a particular protein.

Mutations may be neutral when they don't show an apparent effect on the phenotype of an organism such as occur in mutations located in intergenic regions.

Therefore, with this data, we can see that a genetic mutation may alter the proteins produced by an organism which has a direct effect on the phenotype by altering the structures that it is able to synthesize.

Learn more about genetic mutations here:

https://brainly.com/question/29000870

#SPJ1

If light moves through an optical medium at a speed of 2.5 x 108 m/s, the media's refractive index is 1.2.

The material's refractive index (n) may be defined as -

Refractive Index (n) = Light's speed in a vacuum (C) divided by its light speed in a medium (V)

Therefore, n = C/V  

Given that the speed of light in the medium is V=2.5×10⁻⁸m/s

and the speed of light in the vacuum is C=3.0×10⁻⁸m/s

Therefore, the equation gives us n = C/V

n=3.0×10⁻⁸m/s÷2.5×10⁻⁸m/s,

which equals n=1.2 (Refractive index of the medium).

Refractive index: The refractive index, sometimes called the refraction index in optics, is a dimensionless quantity that describes how efficiently an optical material bends light.

Light: light is the organic substance that activates vision and makes things visible

To know more about vacuum visit this:

https://brainly.com/question/29242274

#SPJ4

The work done by force is negative in the first scenario because the force and displacement are acting in the opposing directions. As the force and displacement are perpendicular in the second condition, there is no work done.

What exactly is a physics "work done"?

The product of a force's component acting in the displacement's vector and its magnitude is known as the work done by the force. Formula. The following formula may be used to calculate work by multiplying force and distance in the direction of the force. Unit: W = F d.

What exactly is a work example?

The following situations include work: relocating a table. a door is pulled and pushed. Walking. raising a stone.

To know more about work done visit:

https://brainly.com/question/16976412

#SPJ1

Sound components are identified as coming from the same sound source. this means that the components are generated by the same physical object or process, and they tend to have similar characteristics such as frequency, timbre, and intensity.

 These components are usually perceived as being part of a single sound or voice, rather than being perceived as separate sounds.

For example, if you are listening to a person speaking, the different sound components that make up their voice, such as their pitch, vowel sounds, and consonant sounds, are all generated by the same source (the person's vocal cords and mouth).

In some cases, sound components can be isolated and analyzed individually. For example, in audio engineering or music production, in order to shape the overall sound of a recording or performance.

Additionally, sound components can be synthesized or manipulated using digital audio software, allowing for the creation of new sounds or the modification of existing ones.

Learn more about Sound from

https://brainly.com/question/29667803
#SPJ1

The wavelength of WFNX’s radio waves with the given speed and frequency is 2.95m.

Wavelength can be defined as the distance between two successive crests or throughs of a wave.

The wavelength of WFNX’s radio waves with the given speed and frequency is 2.95m.

Given data in the question;

Speed of wave; c= 3×10^8

Frequency of wave; 1.017×10^8

wavelength; ?

To determine the wavelength of the radio wave, we use the expression for the relations between wavelength, frequency and speed.

C\f

Where  is wavelength, f is frequency and c is the speed.

We substitute our given values into the equation

=2.95

Therefore, the wavelength of WFNX’s radio waves with the given speed and frequency is 2.95m.

To know more about wavelentgh click-

https://brainly.com/question/10750459

#SPJ1

The magnitude and direction of the magnetic force on a particle of charge is - 2.21 in the opposite direction.

Magnetic force is defined as the electrically charged particles that are in motion and exhibit either attraction or repulsion. The interaction between moving and stationary charged particles is explained by the electromagnetic force, commonly known as the Lorentz force.

The magnitude and direction of the magnetic force can be calculated as

F = q v B sinθ

Given q = 13 C

v = - 20 m/s

B =  0.5 T²

F = 13 C x - 20 m/s x 0.5 T² sinθ

F = - 130 sinθ

Let θ is equal to 1

Then, F = 130 sin1

F = - 130 x 0.017

F = - 2.21

Thus, the magnitude and direction of the magnetic force on a particle of charge is - 2.21 in the opposite direction.

To learn more about magnetic force, refer to the link below:

https://brainly.com/question/3160109

#SPJ1

The critical angles for red and violet light through diamond are 24.5° and 24.0°, respectively.

The incidence on incidence at which the refraction angles equals 90 degrees is known as that of the critical angle. The polarization di incident light and the light beam bends in the direction of normal when it enters a thicker environment from a similarly rarer medium.

The critical angle is the angle of impact that provides a 90-degree angle of refraction. Keep in mind that an angle of impact value is how the angle of inclination is defined. For water-air borders and crown glass-water borders, the angle of inclination would be 48.6 degrees and 61.0 degrees, respectively.

To know more about critical angles visit:

https://brainly.com/question/24796244

#SPJ4

The reason behind action and reaction forces not balance each other out is d)because the action force acts on the carriage, while the reaction force acts on the horse. So, correct option is d.

Forces generally act two by two, which are known as activity and response forces.

The activity force is the power applied to an article by the first activity, and the response force is an equivalent power applied by the item the other way.

A power that is applied to an item is alluded to as an activity force. A response force is the consequence of an inverse heading activity force.

Newton's third law of motion tends to these two forces, alluded to as activity and response powers.

The depicted activity and response powers don't adjust each other out in light of the fact that the activity force follows up on the carriage and the response force follows up on the pony.

Hence, correct option is d.

To know more about action and reaction forces, visit here:

brainly.com/question/13186730

#SPJ4

(Complete question) is:

A horse pulls on a carriage. By Newton's third law, the carriage pulls back on the horse with equal force. Why do the action and reaction forces just described not balance each other out?

A.

because this is not an action--reaction pair

B.

because action and reaction forces are not equal in magnitude in this case

C.

because action and reaction forces act in the same direction in this case

D.

because the action force acts on the carriage, while the reaction force acts on the horse

The vertical impulse by the lift force during this time is 4.15 by minutes for Newton second.

We have a demon That there is a force of 52 down cause of 15. Right? This is what we have you in the questions and acting on the bill. Be both masked by Graham of Mars five g. No. In the meantime. And travelers given that the time and develop acting on this fourth, you should humanists. But we need to find the impulse England's. They seem to not advise you actually. This is what we need to find. So we know that false change in momentum much time. So basically impulses change momentum, but you find impulses changing moment also jay so G is false in campaign so we can put forth here. The forces to do time 59 1 dime. That's Spanish for -5. This was with 15 to 10 days to four minutes, five Newton and two times three seconds Volunteers. They will get 15 into 10 days to the R -4. 15 10 by minus for Newton's second.

To know more about vertical impulse click-

https://brainly.com/question/26152956

#SPJ1

Answer: tbh I think it’s C I did research and says similar about it

Explanation:

A large, moving truck crashes into a small parked car. How do the magnitudes of the impulses and the forces on each vehicle compare during the collision: A The truck receives more force but less impulse.

In physics, value is defined really as “distance or amount.” It depicts absolutely the relative course or length wherein an item actions within the experience of movement. it's far used to specify the scale or scope of something. In physics, value commonly refers to distance or quantity.

Magnitudes are the scale of something. for example, in the case of speed, a vehicle is moving faster than a bike. in this instance, the importance of the speed of the auto is higher than that of the bike. It tells the route or size that is absolute or relative in which an item travels in the experience of motion.

Learn more about Magnitudes here:

https://brainly.com/question/24256733

#SPJ4

Answer:

Explanation:

KE=mv(v)/2

KE=2(1.5)(1,5)/2

KE=2.25

Important Formulas:

[tex]KE=.5mv^2[/tex]

__________________________________________________________

[tex]m=2kg[/tex] (measured in kg)

[tex]v=1.5m/s[/tex] (measured in meter per second)

[tex]KE=?[/tex] (measured in joules)

__________________________________________________________

[tex]KE=.5(2)(1.5)^2[/tex]

[tex]\fbox{KE = 2.25J}[/tex]

Each of the vehicle's six wheels would have a wheel speed sensor, but there would only be four modulators in the six-in/four-out system.

Anti-lock braking systems (ABS) help you manoeuvre in an emergency by restoring traction to your tyres. What It Does: Assists in stopping wheel locking so that the driver may steer to safety. What It Isn't Able To Do The stopping distance might not be lowered, and it's okay if the pedal wobbles or pushes back.

By keeping the brakes from locking, ABS gives the driver better steering control while braking. ABS rarely activates, unless you reside in a state with lots of snow and ice. It groans and rattles when it does. Many motorists claim that they feel as though their brakes had failed.

The main drawback of ABS brakes is the additional expense that it adds to the base price of a vehicle. Additionally, maintenance expenses increase since each wheel's pricey sensors might be expensive to replace if they become out of calibration. Anti-lock brakes' primary function is to offer sure-footed braking.

To know more about ABS visit:

https://brainly.com/question/8555918

#SPJ4

At a distance of 15 cm, the magnetic field strength (measured in microteslas) is 0.68 T.

A magnetic field, a vector field that describes the magnetic influence on moving electric charges, electric currents, and magnetic materials.  The magnetic field is the area in which a magnet produces its magnetic effects. We use the magnetic field as a tool to describe how the magnetic force is distributed in the vicinity and inside something magnetic in nature.

Magnetism is created by moving electric charges. The tiniest units of matter are known as atoms. Each atom contains charged particles called electrons. The nucleus, or core, of an atom is made up of electrons that spin like tops.

The Earth's magnetic field (and surface magnetic field) has two poles, one close to the planet's geographic north pole (see Magnetic North Pole) and the other close to its geographic south pole. Together, these poles resemble a magnetic dipole (see Magnetic South Pole).

Formula to calculate magnetic field around a wire:

B=(μ_° I)/2πd

B = The strength of magnetic field (Tesla)

μ₀ = permeability of free space = 4π × 10⁻⁷ T/mA

I = the current (Ampere)

π = 3.14

d = distance from the wire (m)

Given

I = 1.70 A

D=15.0 cm

B=(μ_° I)/2πd

B=(4π × 10⁻⁷×1.70)/2πd

B=(2 × 10⁻⁷×1.70)/d

B=(3.4× 10⁻⁷)/15

B=0.68×〖10〗^(-6)

B=0.68μT

To know more about Magnetic Field visit:

https://brainly.com/question/23096032

#SPJ4

There wouldn't be any light and dark phases if the axis were adjusted so that it was absolutely upright. Since winter will usually prevail in the Southern Hemisphere, this alteration would not be unexpected on Earth.

In planar geometry, an angle is a shape made up of two rays or lines that share an endpoint. The common terminal of two rays is known as the vertex, and the two rays are referred to as sides of an angle. The Latin word "angulus," which means "corner," is the basis of the English name "angle." In Euclidean geometry, an angle is a shape composed of two rays, referred to as the angle's sides and vertices, respectively, and having a common terminus. Two rays can form angles in the plane where they are positioned.

One can measure and calculate angles in terms of degrees with a protractor. The black arrow in the figure below, for instance, uses a protractor to point to 100°, crossing 90°. Consequently, the angle has a size of 100°.

To know more about Angle visit:

https://brainly.com/question/22819767

#SPJ4

Yes, the pivot point (i.e., the triangle in the diagram upon which the ruler balances) exert a force on the ruler. No, it does not exert a nonzero torque about the pivot.

Pivot point is that point where an object rotates around. Sometimes, it is called the fulcrum or rotational axis.

A lever has a rigid bar that is able to pivot at one point and this point of rotation is known as the fulcrum. Force is applied at some point away from the fulcrum.

Torque is a measure of how much force acting on the object causes that object to rotate. The object rotates about an axis, which is called as the pivot point.

To know more about pivot point, refer

https://brainly.com/question/14516358

#SPJ4

Answer:

1/ Better Health

2/ Reduce injury posibility

3/ Increase energy level when exercising

4/ Bigger muscle

5/ Prevent disease

Explanation: The training helps you get the five benefits above. There is more benefit, but I think the five above are the most important!

The claim that metals are superior to non-metals in terms of heat and electrical conductivity is true.

Electrochemistry is the study of chemical processes that move electrons. It deals with the interactions between electromagnetic oil and power transformation. Example: The investigation of electrochemical cells is a part of electrochemistry. It involves cells that convert energy into electrical energy.

Electrochemistry has many common applications in daily life. All sorts are batteries, among them those that power lamps, calculators, and automobiles, primarily generate electricity through biochemical reactions. Plating objects with decorative metals like gold or chromium requires electricity.

To know more about Electrochemical visit:

https://brainly.com/question/12034258

#SPJ4

Answer:

D

Explanation:

More pressure pushes more gas into the solvent

   think about the opposite when you open a soda and decrease the pressure....the gas comes out of solution....

Objects such as the great nebula in andromeda were once called extragalactic nebulae. it is now realized that other galaxies much like our own.

A nebula is a distinctively luminous region of the interstellar medium, which may be made up of cosmic dust, neutral, neutrally ionised, or molecular hydrogen. Nebulae are frequently areas where stars are being formed, as seen in the Eagle Nebula's "Pillars of Creation."

The gas, dust, and other material formations in these areas "clump" together to form denser regions, which draw in more matter and finally reach a density where stars can form. Planets and other planetary system objects are then supposed to be formed from the leftover material.

Learn more about nebula here:

https://brainly.com/question/9497068

#SPJ1

One important way astronomers can learn in some detail about what happens when galaxies collide is to simulate galaxy collisions on a large computer and watch what the simulation predicts.

Simulating galaxy collisions on a large computer allows astronomers to observe how galaxies interact and evolve when they collide.

They can observe how stars, dust, and gas interact, how the shape of the galaxies change, how the distribution of stars changes, and how the total mass of the galaxies is affected.

They can also observe how the collision affects the gas and dust, and how they form new stars, as well as how subsequent collisions can cause the galaxies to merge completely. Simulations provide a powerful tool to gain insight into the complexities of galaxy collisions and to understand how galaxies form, evolve, and interact.

Learn more about the galaxies collide:

https://brainly.com/question/25123335

#SPJ4