Answer:
S waves are transverse and cannot travel through liquids. P waves are longitudinal and can travel through liquids. When an earthquake happens on one side of the Earth, P and S waves can be detected all around the world. S waves cannot be detected on the opposite side of the earth but can be detected at angles less than or equal to 90 degrees or slightly more. This is because there is a liquid core in the centre of the earth preventing the S waves from travelling to the direct opposite side of the Earth. P waves can be detected all around the world
Explanation:
A car travels 50 km in 10 hr. What was the average speed of the car?
Answer:
5km
Explanation:
Just helping
If 50km divided by 10hrs =5
Sorry if I'm wrong but that's what I got
What are the advantages of ring system wiring?
Answer:
The two most common advantages of the ring system are as follows:
- Voltage drop across the circuit is less or negligible when compared with the tree system.
- More appliances can be connected across the circuits as the supply is radially distributed across the space
We have that the advantages of ring system wiring is given as
Voltage drop across the circuit very smallMore load space is available as the supply point is distributed across the circuitRing Wiring
Question Parameters:
Generally, A ring system wiring is wiring method where we see the sockets and distribution outlets to be connected in a ring-like manner.
We have that its advantage are
Voltage drop across the circuit very smallMore load space is available as the supply point is distributed across the circuitFor more information on Electricity visit
https://brainly.com/question/9383604
how long did it take the flag to rotate once in a full circle
Answer:
360 degrees is one full rotation starting at zero
it take 2 s to the flag to rotate once in a full circle with 3 rad/s of angular velocity.
What is Angular velocity and acceleration ?Angular velocity is "rate of change of angular displacement with respect to time". i.e. ω= dθ/dt. it is also defined as angular displacement over time. i.e. ω = angular displacement/Time.
Angular velocity shows how much angle can be covered in unit time. It's SI unit rad/s.
Angular acceleration is rate of change of Angular velocity with respect to time.
i.e. α = dω/dt if an object changes its angular velocity in short time, we can say that it has greater angular acceleration. It is expressed in rad/s².
In this problem we have to calculate time, but the angular velocity id not given.
Consider the angular velocity is 3 rad/s.
Given,
Angular displacement θ = 2π
angular velocity ω = 3 rad/s
Time t = ?
Time = θ/ω
Time = 2π/3 rad/s = 2 s
Hence the answer is 2s.
To know more about angular velocity :
https://brainly.com/question/29557272
#SPJ2.
Please help
How would u define energy
Energy is being produced in two different ways.
1st. when you run, exercise, etc allot of energy is being produced from your body in form of heat.
2nd. energy which is in form of coal, electricity, gas etc.
Definition: the capacity for doing work. It may exist in potential, kinetic, thermal, electrical, chemical, nuclear, or other various forms. There are, moreover, heat and work—i.e., energy in the process of transfer from one body to another.
hope this helps you
have a great day :)
[tex]\qquad \qquad\huge \underline{\boxed{\sf question}}[/tex]
How do you find the coordinates of centre of mass of multiple particle system ?
By dividing the moments around the y-axis and around the x-axis,
respectively, by the total mass, the x- and y-coordinates of the centre of
mass may be determined.
formula's:
[tex]y.cm=\left[\begin{array}{ccc}\frac{m1y1+m2y2+...}{m1+m2+...}\end{array}\right][/tex][tex]x.cm=\left[\begin{array}{ccc}\frac{m1x1+m2x2+....}{m1+m2+.....}\end{array}\right][/tex]centre of two mass particle system: [tex]\left[\begin{array}{ccc}(m1+m2) r.cm =(m1 )r1+(m2) r2\end{array}\right][/tex]How much force is needed to accelerate an object of mass 90 kg at a rate of 1.2 m/s2?
0.013 N
75 N
108 N
1080 N
Answer:
108 N
Explanation:
F = ma
F = (90kg)(1.2m/s^2)
F = 108 N
Two large parallel metal plates are 6.0 cm apart. The magnitude of the electric field between them is 600 N/C. What work is done when one electron is moved from the positive to the negative plate? Note: the charge of an electron is 1.6 x 10-19 C.
3.36 x 10-20 J
4.98 x 10-17 J
1.6 x 10-19 J
5.76 x 10-18 J
Answer:
Approximately [tex]5.76 \times 10^{-18}\; {\rm J}[/tex] (by the external force that moved the electron.)
Explanation:
Let [tex]q[/tex] denote the magnitude of a charge in an electric field of magnitude [tex]E[/tex]. The magnitude of the electrostatic force on that charge would be:
[tex]F = q\, E[/tex].
In the electric field in this question, the magnitude of the electric force on the electron would be:
[tex]\begin{aligned}F &= q\, E \\ &= 1.6 \times 10^{-19}\; {\rm C} \times 600\; {\rm N \cdot C^{-1}} \\ &= 9.6 \times 10^{-17} \; {\rm N}\end{aligned}[/tex].
Moving the electron to the other plate would thus require an external force of [tex]9.6 \times 10^{-17}\; {\rm N}[/tex].
This force needs to be exerted over a distance of [tex]6.0\; {\rm cm}[/tex] ([tex]6.0 \times 10^{-2}\; {\rm m}[/tex].) The direction of the motion is the same direction as that of the external force. Thus, the work that needs to be done would be:
[tex]\begin{aligned}W &= F\, s \\ &\approx 9.6 \times 10^{-17}\; {\rm N} \times 6.0 \times 10^{-2}\; {\rm m} \\ &\approx 5.76 \times 10^{-18}\; {\rm J}\end{aligned}[/tex].
Two carts collide and bounce apart. Cart 1 had a momentum of –6 kg • m/s before the collision. Cart 2 had a momentum of 10 kg • m/s before the collision.
What is the total momentum of the carts after the collision?
–16 kg • m/s
–10 kg • m/s
4 kg • m/s
10 kg • m/s
Answer:
4 kg m/s
Explanation:
When finding momentum after a collision, you can just add the momentums together, this would be 10 kgm/s -6 kgm/s to get 4 kgm/s
The total momentum of the carts after the collision is 4 kgm/s.
What is momentum?The momentum of an object is the product of mass and velocity of the object.
P = mv
Total momentum of the cartsThe total momentum of the carts is calculated as follows;
P = P₁ + P₂
P = -6 + 10
P = 4 kgm/s
Thus, the total momentum of the carts after the collision is 4 kgm/s.
Learn more about momentum here: https://brainly.com/question/7538238
Please help me. I have to submit this today.
If the mass of the cement is 15 000 kg, calculate the density of this cement sample in kgm-3
Explanation:
Hi there!
Mass of the container (m) = 15000 kg
Also from the figure;
Volume of the container (V) = l*b*h
{ From figure length = 2m , breadth = 1.1m, height = 2.5m}
So,
V = (2*1.1*2.5) m³
= 5.5m³
Then;
Density (d) = m/v
= 15000/5.5
= 2727.27 kgm³
Therefore, the density is 2727.27 kgm³.
Hope it helps!
2. Which is NOT a unit of speed?
A. kilometer/hour
B. meter/second
C. miles/hour
D. second/meter
Please help me with this question
Answer:
D
Explanation:
the energy increased so the amplitude got taller and the wave length got shorter.
FOR THOSE SMARTIES!! If the speed of an object is doubled, which of the following must also double?
a. the mass of the object
b. the kinetic energy of the object
c. the gravitational potential energy of the object
d. none of these
Answer:
i think b sorry if im wrong!
Explanation:
hello I need the formula for getting the focal length of a concave mirror
10. With a class 1 lever, does mechanical advantage increase or decrease as the fulcrum is moved closer to the load? Explain why.
Answer:
Class 1 Levers: Moving the fulcrum closer to the load will increase the mechanical advantage. Moving the effort farther from the fulcrum will increase the mechanical advantage.
Explanation:
Hope it helps you
what does displacement mean in an equation?
Derive P=4T/R from fluid mechanics
To Find: Diameter of soap bubble =? Solution: By Laplace's law of spherical membrane for a bubble. (Pi– Po) = 4T / r.
On a fake planet, you find that on a certain day at noon no shadow is cast. At the same time your friend sees a shadow due to the Sun being 12 degrees away from the Zenith. Knowing the distance between you and your friend is 500 km, what is the circumference of this fake planet
Answer:
In 250 BC, Eratosthenes measured the circumference to be about 24,500 miles:
by this method, 12 deg = 12 / 360 = 1/30 of the planet's surface\
30 * 500 km = 15,000 km in circumference, about 9,200 miles
Three horizontal forces are pulling on a
ring, at rest. Fy is 6.25 N at a 180° angle,
and F2 is 8.90 N at a 243° direction. What
is the x-component of F3?
Answer:
-(F1+F2)y
Explanation:
add up F1 and F2 using x-y components
Since the three forces balance,
F3y = -(F1+F2)y
Answer: 10.29
Explanation:
F1: 6.25cos(180°) = -6.25
F2: 8.90cos(243°) = -4.04
F3: -6.25 + (-4.04) = 10.29
When greater pressure is applied to the accelerator to increase speed to pass someone or merge it is called _________ acceleration.
Thrust acceleration is the application of great pressure to the accelerator to increase speed.
Thrust acceleration
Thrust accelerationGenerally,greater pressure is applied to the accelerator it is obvious that the driver of the system is making an attempt to increase speed of the system for a specific time frame
Therefore, when greater pressure is applied to the accelerator to increase speed it is refereed to as thrust acceleration.
For more information on Speed
https://brainly.com/question/4931057
5. An object placed 3m from a plane mirror is shifted by 1 m away from the mirror. What is the distance between the object and its image?
Answer:
distance of object from mirror=distance of image from mirror
so distance between object and image=distance of object from mirror+distance of image from mirror
=2 x distance of object from mirror
=2 x (3+0.4)m
=2 x (3.4)m
=6.8 m
Explanation:
hope this helps :)
Find the number of electrons in the subshell with azimuthal quantum number l=2
Answer:
23 electrons
Explanation:
i just know because im a god
Which group of objects refract light energy?
A.Shiny object, glasses and mirror
B.glasses, prism, and passing through water
C.Glasses, prism and mirror
D.Mirror, glasses, and passing through water
Answer:
B. glasses, prism, and passing through water
Explanation:
Mirrors reflect, not refract.Glasses, water and prism refract.*Note:- When light is bounced back it is called reflection.
[tex]\red{ \rule{35pt}{2pt}} \orange{ \rule{35pt}{2pt}} \color{yellow}{ \rule{35pt} {2pt}} \green{ \rule{35pt} {2pt}} \blue{ \rule{35pt} {2pt}} \purple{ \rule{35pt} {2pt}}[/tex]
Answer⤵️Which group of objects refract light energy?
B.glasses, prism, and passing through waterwhich technology is applied in a plough?
Answer:
sulphite is what equation
Explanation:
gas
liquid
solid
aqueous
A catapult is a device that throws heavy stones. The stone sits in a basket at the end of an arm. The arm moves fast, and the stone is launched toward the target. What type of force does the catapult apply to the stone
Elastic force is the type of force which the catapult applies to the stone.
What is a Catapult?This is a launching device which is composed of rubber and used in the study of projectile motion.
The type of force present in a rubber is elastic force which is applied as a result of pressure on it when the individual launches the stone towards the required target.
Read more about Elastic force here https://brainly.com/question/5055063
The catapult applies elastic force to the stone which is converted to kinetic energy of the flying stone.
What Elastic potential energy?Elastic potential energy is the type of energy that is stored in an elastic material.
The catapult is an elastic material that converts elastic energy into kinetic energy of flying stone.
Thus, the catapult applies elastic force to the stone which is converted to kinetic energy of the flying stone.
Learn more about elastic potential energy here: https://brainly.com/question/25996974
A 45 kg object has a momentum of 225 kg-m/s northward. What is the object's velocity?
A. 5.0 m/s
B. 180 m/s
C. 10,125 m/s
D. 0.20 m/s
Answer:
Momentum = m x v
225 = 45 x v
÷45
5 = v
Velocity is 5m/s
Answer is A
Hope this helps!
Explain how the writing on the arm let, specified in paragraph 4, contributes to the development of the story. The story “The Water Of Life”
Answer:
Answer:
This week in class, we’re reading "The Water of Life" by Howard Pyle.
In Howard Pyle’s “The Water of Life”, a king abuses his power by asking a faithful servant to complete difficult tasks for him, hoping to win the love of a princess.
As we read, we will be discussing the themes of Morality, Power & Greed, and Resilience & Success as they relate to the text. We are trying to answer these big questions :
"What is good and how do we know?", "Why do people succeed?", and "How does power corrupt?"
Explanation:
Answer:
Explanation:
It is not exactly a physics question...
The story "The Water Of Life" is about a king and his faithful servant.
The servant worn an armlet on his arm.
The following words were written on the armlet: Who thinks to wear me on an arm, must lack both guile and thought of harm."
That writing further develops the story as it reflects on the king's sending his servant to help a princess who was upset after her bird died. The story's theme is about power, greed and resilience.
Calculate the slope of the line on the graph using the formula:
m = m = v subscript 2 - v subscript 1 over x subscript 2 minus x subscript 1.
The slope of the line is
m/s.
From the given graph of position v/s time, the velocity can be determined by calculating the slope of the linear curve. The slope of the line is 4 m/s.
What is velocity?Velocity of an object is the measure of the distance it travelled per unit time. Velocity is a vector quantity having magnitude and direction. It has the common unit of m/s.
Velocity is the ratio of change in distance to the change in time. Hence, let Δx be the distance and Δt be the time change.Then velocity is :
v = Δx / Δt .
In the given graph the distance covered within 2 seconds is 8 m. Then the velocity is :
v = 8/2 = 4 m/s.
It is the slope of the linear curve in the graph. Therefore, the velocity of the object is 4 m/s.
To find more on velocity, refer here:
https://brainly.com/question/18084516
#SPJ2
Answer:
From the given graph of position v/s time, the velocity can be determined by calculating the slope of the linear curve. The slope of the line is 4 m/s.
Explanation:
it is right
Ignoring the sign, which has a greater magnitude of charge?.
Answer:
the car
Explanation:
Does a magnetic field require any tr ansfer or movement of mass or particles?
Answer:
The magnetic influence on moving electric charges, electric currents, and magnetic materials is described by a magnetic field, which is a vector field. In a magnetic field, a moving charge experiences a force that is perpendicular to both its own velocity and the magnetic field. The magnetic field of a permanent magnet attracts or repels other magnets, as well as ferromagnetic elements like iron. Furthermore, a varying magnetic field exerts a force on a variety of non-magnetic materials by changing the mobility of their outer atomic electrons.
Explanation:
:) hope this helps