Determine the resultant R of the two forces applied to the bracket.
Write R in terms of unit vectors along the x- and y-axes shown.
The written form of R in terms of unit vectors along the x- and y-axes shown are; R Cos θ and R sin θ respectively.
Resolving forces along the x- and y-axesGiven that the force R, which is the resultant of the unit vectors given has magnitude R;
It follows that the resolved form of unit vector, R along the x- and y- axes is;
R(x) = R Cos θR(y) = R sin θ.Where, angle measure, θ = angle subtended by the resultant force with the horizontal.
Read more on resultant force;
https://brainly.com/question/26491134
In python, how would I randomize numbers and insert them into a file?
If you were to carve a wooden statue what tool would you use?
A: Chisel
B: Hand Saw
C: Hack Saw
D: Tin Snips
Answer:
You would have to use a chisel.
.Explanation:.
.
How would I find the Voltage across the open circuit
Answer:
Vab = 80V
Explanation:
The only current flowing in the circuit is supplied by the 100 V source. Its only load is the 40+60 ohm series circuit attached, so the current in that loop is (100V)/(40+60Ω) = 1A. That means V1 = (1A)(60Ω) = 60V.
Vab will be the sum of voltages around the right-side "loop" between terminals 'a' and 'b'. It is (working clockwise from terminal 'b') ...
Vab = -10V +60V +(0A×10Ω) +30V
Vab = 80V
All of these are types of wheel alignments EXCEPT:
A) four-wheel.
B) steering angle.
C) two-wheel.
D) thrust angle.
Answer:
thrust angle
Explanation:
good luck.........
Breaking on may cause a loss of control
Answer:
Is there supposed to be a picture...try asking question again
A turbine engine compressor which contains vanes on one side of the impeller is a
1. Single entry centrifugal flow compressor
2. Single entry axial flow compressor
3. Double entry axial flow compressor
4. Double entry centrifugal compressor
The turbine engine described above is a Single-entry Centrifugal Compressor.
What is a Single-entry Centrifugal Compressor?
Also known as a Single-Stage Centrifugal compressor, this type of engine combines one impeller with an inlet guide vane that is associated and a diffuser.
It is used for increasing the kinetic energy of the gas with a high-speed impeller. This energy is then converted into heightened pressure within the diffuser. The correct answer, thus, is A.
In order words, they are used for compressing large volumes of gas into small pressures.
See the link below for more about turbine engines:
https://brainly.com/question/894340
10.) A solid circular titanium control rod at 7,000 lb axial tension force where stress must not
exceed 42,000 psi. Assume that the modulus of elasticity of the titanium is 16,500,000 psi
and that the rod must elongate no more than 0.20 in. Determine (a) the minimum rod
diameter (precision 0.00) and (b) the maximum rod length (precision of 1).
The minimum rod diameter is 0.46 in and the maximum rod length is 78.6 in.
What is diameter?Diameter is defined as the distance that runs through the center of a circle from one point to another on its surface. It can also be thought of as the circle's longest chord. The diameter of a sphere can be defined using either of the two methods.
Given tension axial force = 7000 lb
Maximum axial tensile strength = 42000 psi
σ = P /A = P / λ / 4 x d²
The minimum rod diameter = 0.46
Elongation in rod = 0.2 in
= FL / AE
Maximum length of rod = 78.6 in
Thus, the minimum rod diameter is 0.46 in and the maximum rod length is 78.6 in.
To learn more about diameter, refer to the link below:
https://brainly.com/question/13624974
#SPJ1
2. To read and understand electrical blueprints, you need to know
O A. the fundamentals of electrical engineering.
O B. how to sketch a plan view.
C. how buildings are constructed.
O D. the meaning of electric symbols.
Answer:
To read electrical blueprints one must understand the flow of the circuit, identify critical nodes, understand Ohm’s Law, [ and have a deep comprehension of the National Electrical Code. ]
Explanation:
Water flows through a horizontal branching pipe as shown
in Fig. P3.109. Determine the pressure at section (3).
The pressure of the water in section 3 of the horizontal pipe is -945 kPa.
Volumetric flow rate at equilibrium
The volumetric flow rate at equilibrium is given as flows;
mass in = mass out
[tex]Q_1 = Q_2 + Q_3[/tex]
where;
Q1 is the flow rate in section 1Q2 is the flow rate in section 2Q3 is the flow rate in section 3Pressure of water in section 3The pressure of water in section 3 of the horizontal pipe is calculated as follows;
[tex]F_2 + F_3 = F_1\\\\\frac{P_2}{A_2} + \frac{P_3}{A_3} = \frac{P_1}{A_1} \\\\\frac{350\ kPa}{0.02} + \frac{P_3}{0.07} = \frac{400 \ kPa}{0.1}\\\\\\frac{P_3}{0.07} = \frac{400 \ kPa}{0.1} - \frac{350\ kPa}{0.02} \\\\\frac{P_3}{0.07} = 4000 \ kPa/m^2 \ - \ 17,500 \ kPa/m^2\\\\\frac{P_3}{0.07} = -13,500 \ kPa/m^2 \\\\P_3 = 0.07 \ m^2 \ \ \times \ \ -13,500 \ kPa/m^2\\\\P_3 = -945 \ kPa[/tex]
Thus, the pressure of the water in section 3 of the horizontal pipe is -945 kPa.
Learn more about flow rate here: https://brainly.com/question/21630019
Drag the tiles to the correct boxes to complete the pairs.
Match the type of manufacturing system to its description.
agile manufacturing system
assembly line production system
lean manufacturing system
mass production system
focuses on manufacturing large and
continuous product runs.
arrowRight
focuses on the reduction of waste in the
manufacturing process
arrowRight
focuses on the ability to adapt to
customer and market changes
arrowRight
focuses on improving worker efficiency
by making tasks short and repetitive
arrowRight
The correct matching would be:
Mass production system -> focuses on manufacturing large and continuous product runs.
The other matching pairsLean manufacturing system -> focuses on the reduction of waste in the manufacturing process.
Agile manufacturing system -> focuses on the ability to adapt to customer and market changes.
Assembly line production system -> focuses on improving worker efficiency by making tasks short and repetitive.
The mass production system emphasizes the production of a high volume of products in a consistent manner. The lean manufacturing system has the objective of minimizing or eliminating waste.
The agile manufacturing system places great importance on accommodating alterations from customers and the market. The assembly line manufacturing technique enhances worker productivity by assigning brief and repetitive tasks.
Read more about mass production system here:
https://brainly.com/question/8689792
#SPJ1
Technician A says that reversing the direction of refrigerant (as with a heat pump system) could be done to provide cabin heat. Technician B says that the amount of energy loss from the traditional drive belt and electric clutch A/C system is too high for hybrid and electric vehicles. Who is correct?
It can be noted that technician B is correct as amount of energy loss from the traditional drive belt and electric clutch A/C system is too high for hybrid and electric vehicles.
What is energy?Energy simply means the property that is transferred to a body.
In this case, Technician A says that reversing the direction of refrigerant as with a heat pump system could be done to provide cabin heat. This is incorrect because this is done to remove heat.
Therefore, the correct person is technician B.
Learn more about energy on:
https://brainly.com/question/19665326
Which Reynolds number would (most likely) correspond to a system where radial variations in velocity were negligible
a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Answer:
I agree
Explanation:
Answer:
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
funny question of no reason but k
Explanation:
Whats the purpose of the keyway
Answer:
abrir candados y abrir puertas
Explanation:
who ever answers this gets 25 NON COSTLY points
Answer:
"cool"
Explanation:
) How much dry salt must be added in 150 kg of aqueous salt solution in order to
increase its concentration from 15% to 40%? (10 Marks.
To archive a concentration of 40%, you need to add 62.5 kg of salt.
How much salt must we add?
First, we have 150kg of aqueous salt solution with a concentration of the 15%, which means that the 15% of 150kg is salt, so we have:
0.15*150kg = 22.5 kg of salt.
Now we want to add a quantity M of salt, such that the new concentration of salt is of 40%.
The new mass of the mixture will be:
150kg + M
The new mass of salt will be:
22.5kg + M
The concentration of salt, in decimal form, will be:
(22.5kg + M)/(150kg + M)
The above quotient must be equal to 0.4 (40% in decimal form), then we solve:
(22.5kg + M)/(150kg + M) = 0.4
(22.5kg + M) = 0.4*(150kg + M)
(22.5kg + M) = 60kg + 0.4*M
M - 0.4*M = 60kg - 22.5kg
0.6*M = 37.5kg
M = (37.5 kg)/0.6 = 62.5kg
So you need to add 62.5kg of salt.
If you want to learn more about concentrations, you can read:
https://brainly.in/question/14278665
It is given that 50 kg/sec of air at 288.2k is iesntropically compressed from 1 to 12 atm. Assuming a calorically perfect gas, determines the exit temperature and the compressor's input power.
The exit temperature is 586.18K and compressor input power is 14973.53kW
Data;
Mass = 50kg/sT = 288.2KP1 = 1atmP2 = 12 atmExit TemperatureThe exit temperature of the gas can be calculated isentropically as
[tex]\frac{T_2}{T_1} = (\frac{P_2}{P_1})^\frac{y-1}{y}\\ y = 1.4\\ C_p= 1.005 Kj/kg.K\\[/tex]
Let's substitute the values into the formula
[tex]\frac{T_2}{T_1} = (\frac{P_2}{P_1})^\frac{y-1}{y} \\\frac{T_2}{288.2} = (\frac{12}{1})^\frac{1.4-1}{1.4} \\ T_2 = 586.18K[/tex]
The exit temperature is 586.18K
The Compressor input powerThe compressor input power is calculated as
[tex]P= mC_p(T_2-T_1)\\P = 50*1.005*(586.18-288.2)\\P= 14973.53kW[/tex]
The compressor input power is 14973.53kW
Learn more on exit temperature and compressor input power here;
https://brainly.com/question/16699941
https://brainly.com/question/10121263
what is the difference between chemical engineering and medical engineering
Explanation:
Medical engineering is narrowed to medicine and biology for healthcare including the development of medical treatments, applications or diagnostic technologies etc...
Answer:
A
tyler has a points card for a movie theater.
he receives 75 rewards points just for signing up.
• he earns 10.5 points for each visit to the movie theater.
he needs 180 points for a free movie ticket.
.
a
how many visits must tyler make to earn a free movie ticket?
Explanation:
Which option explains the benefit of a newly designed fluid power system in the following scenario? A new fluid power rail system is being designed to travel across a large expanse of China. The new system will have a state-of-the-art hydraulic power system. The new fluid power system will have microstructures in the inner tubing to decrease friction and allow for more efficient dispersion of the fluid. The new fluid power system will have microstructures in the inner tubing to decrease friction and allow for more efficient dispersion of the fluid. The new fluid power system will have microstructures in the inner tubing to increase friction and allow for more efficient dispersion of the fluid. The new fluid power system will have microstructures in the inner tubing to increase friction and allow for more efficient dispersion of the fluid. The new fluid power system will have smooth surfaces to decrease friction and allow for more efficient dispersion of the fluid. The new fluid power system will have smooth surfaces to decrease friction and allow for more efficient dispersion of the fluid. The new fluid power system will have smooth surfaces to increase friction and allow for more efficient dispersion of the fluid.
Answer:
B
Explanation:
Answer:
The new fluid power system will have microstructures in the inner tubing to increase friction and allow for more efficient dispersion of the fluid.
Explanation:
What hardware and peripherals are you using right now to take this course? What software and operating system (OS)? Describe the basic details of how the things you write for this course are sent through the internet, including the role of packets, an ISP, and a server.
The hardware that I am using to take this course is a Laptop computer running on windows operating system.
What are the basic details of how the things written for this course are sent through the internet, including the role of packets, an ISP, and a server.When you send a query, like your previous message, your laptop's operating system breaks it into smaller units called packets. These packets contain parts of your message, destination address, and other metadata.
They're sent over the internet through your Internet Service Provider (ISP), which directs them through routers and switches. These network devices ensure packets take the most efficient path.
They reach the server where I'm hosted. The server processes your query, generates a response, divides it into packets, sends them back through the same process, and your laptop reassembles them to display my answer.
Learn more about hardware at:
https://brainly.com/question/24231393
#SPJ3
A basic 3-input logic circuit has a LOW on one input and a HIGH on the other two inputs, and the output is LOW. What type of logic circuit is it
Answer:
any of AND, NOR, XOR
Explanation:
An AND gate will give a Low output for any input Low. The logic circuit could be an AND gate.
A NOR gate will give a Low output for any input High. The logic circuit could be a NOR gate.
An XOR gate will give a Low output for an even number of High inputs. The logic circuit could be an XOR gate.
The logic circuit could be any of ...
AND or NOR or XOR
__
Additional comment
What you consider a "basic" gate is not defined here. All of these are catalog items. If you consider only AND, OR, and NOT to be the basic gates, then your answer is AND.
Rear axles are usually lubricated by the same gear oil that lubricates the differential. True or false
Answer:
true
Explanation:
what is the meaning of ultrametric problem?
FD=CD*((P*(V^2)*A)/2)
Please solve for V
Answer:
The answer is V = √2FD ÷ CD × PA
Explanation:
FD = CD × PV²A ÷ 2
V² = 2FD ÷ CD × PA
V = √2FD ÷ CD × PA
Thus, The value of V is V = √2FD ÷ CD × PA
-TheUnknownScientist 72
The load is 200g and is 5' away from
the fulcrum, what is the mechanical
advantage and how many newtons of
force needed to lift the load?
Answer:
In 1st class levers, the fulcrum is always between the effort force and the load. It may or may not provide a mechanical advantage, depending on the location.
Explanation:
Given: A=1, B=1, C=1 for a 3-input NOR gate, what is the output value?
Answer:
0
Explanation:
A NOR gate gives you the inverted output of an OR function. In numerical terms, the OR function gives you the maximum of the inputs:
A+B+C = max(A, B, C) = max(1, 1, 1) = 1
Then the output of the NOR function is its inverse:
(A+B+C)' = (1 -max(A, B, C)) = 1 -1 = 0
The output value is 0.
What is the purpose of encryption?
Answer:
Encryption enhances the security of a message or file by scrambling the content. To encrypt a message, you need the right key, and you need the right key to decrypt it as well.It is the most effective way to hide communication via encoded information where the sender and the recipient hold the key to decipher data.
invent a machine that helps our environment to lessen plastics? draw and explain
Answer: 1. Capturing fibers shed from tyres
The Tyre Collective start-up describes tyres as “the stealthy pollutant you never thought about.”
“It’s common knowledge that tyres wear down, but nobody seems to think about where it goes, and we were really shocked to discover that tyre particles are the second-largest microplastic pollution [after single-use plastics] in our oceans,” Hugo Richardson, one of co-founders of the company, said.
The particles from tyres also infuse into the air we breathe, making up to 50% of air particle emissions from road transport.
Explanation:
two importance of
headlight alignment
Answer:
Proper horizontal and vertical adjustments.
Explanation:
Proper horizontal and vertical adjustments will ensure that you can see far enough down the road to react to obstacles or avoid animals.