In low-speed external water flow over a bluff object, vortices are shed from the object. The vortex shedding produced by a particular object is to be studied in a water tunnel at a 1/4 scale model (model 1/4 the size of the prototype). After a dimensional study, it is found that the Pi terms of this phenomenon are the Reynolds number and the Strouhal number:Re = pVd/muSt = fd/Vwhere f is the frequency of the vortex shedding, V the velocity of the flow, d the characteristic length of the object, and p and mu the density and viscosity of the flow. 1. If the prototype speed is 7 m/s, determine the water velocity in the tunnel for the model tests. 2. If the model tests of part 1 produced a model shedding frequency of 200 Hz, determine the expected vortex shedding frequency on the prototype.

Answer:

1) the water velocity in the tunnel for the model tests is 28 m/s

2) the expected vortex shedding frequency on the prototype is 12.5 Hz

Explanation:

Given the data in the question;

1)

using the Reynolds number relation for prototype and model,

PpVpdp/mu(Prototype) = PmVmdm/mu(for model)

but we know that, density and viscosity in prototype and model will remain same so;

Vp × dp = Vm × dm

vm = Vp × dp/dm

we substitute

vm = 7 m/s × 4

vm = 28 m/s

Therefore, the water velocity in the tunnel for the model tests is 28 m/s

2)

we make use of the Strouhal number relation as given in the question;

fp × dp/Vp = fm × dm/Vm

frequency of the prototype will be;

fp = fm × dm/Vm / dp/Vp

we substitute

fp = 200 × 7 / ( 4 × 28 )

fp = 1400 / 112

fp = 12.5 Hz

Therefore, the expected vortex shedding frequency on the prototype is 12.5 Hz

is a baby duck swimming in a lake a learned behavior

Also discuss how bandwidth is affected by increasing the number of signal elements.

Air is a....
O Solid
O Liquid
O Gas
O Plasma

In this lab, we assumed that the flip-flops did not contribute to the timing constraints of the circuit. Unfortunately, this is not the case. As you saw when you simulated the D flip-flop, the sampling action does not happen instantaneously. In fact, a flip-flop will become unstable if the inputs do not remain stable for a certain amount of time prior to the rising-edge event (setup time) and a certain amount of time after the rising-edge event (hold time). Assume a setup and hold time of 2ns and 1ns, respectively. What would the theoretical maximum clock rate for the synchronous adder be in this scenario

Rainfall rates for successive 20-min period of a 140min storm are 1.5, 1.5, 6.0, 4.0, 1.0, 0.8, and 3.2 in/hr, totaling 6.0in. Determine the rainfall excess during successive 20-min periods by the NRCS method. The soil in the basin belongs to group A. It is an agriculture row crop land with contoured pattern in good hydrologic condition. The soil is in average condition before the storm (moisture condition II).

Sarah is a site investigator for a large construction firm. She is considering Miguel, a former geology student with experience as an intern at an architecture firm, for an assistant site investigation position. Which of the following is most relevant to her decision?

Suppose we are given three boxes, Box A contains 20 light bulbs, of which 10 are defective, Box B contains 15 light bulbs, of which 7 are defective and Box C contains 10 light bulbs, of which 5 are defective. We select a box at random and then draw a light bulb from that box at random. (a) What is the probability that the bulb is defective? (b) What is the probability that the bulb is good?​

You would use a _____________ gauge to check the pressure in each tire. A technician should compare the tire-pressure reading with the tire pressure specified on the side of the driver's _____________ . When servicing tires follow the _____________ procedure outlined in the owner’s manual or online service information. Correct tire-inflation pressure is printed on a placard on the _____________. Why are tires rotated? Which tire rotation method is most often recommended? _____________ An easy way to remember effective tire rotation is, “Drive wheels straight, _____________ the nondrive wheels.” A _____________ is used to ensure that the proper torque is completed on a

Water vapor at 5 bar, 3208C enters a turbine operating at steady state with a volumetric flow rate of 0.65 m3/s and expands adiabatically to an exit state of 1 bar, 1608C. Kinetic and potential energy effects are negligible. Determine for the turbine (a) the power developed, in kW, (b) the rate of entropy production, in kW/K, and (c) the isentropic turbine efficiency.

1. A wastewater treatment plant (WWTP) releases effluent into a stream with mean depth 2 m and mean velocity 0.75 m/s. The BOD concentration at the WWTP is 15 mg/L, and the oxygen deficit is negligible. The deoxygenation rate in the stream is 0.8 d-1 and the reaeration rate is 1.2 d-1. a) Calculate the BOD concentration and DO deficit at a point 20 km downstream from the WWTP. (10 pts) b) What assumptions are inherent in these predictions (give at least two)

Identify the true statements about the lumped system analysis.
A. The entire body temperature remains essentially uniform at all times during a heat transfer process.
B. The temperature of lumped system bodies can be taken to be a function of time only.
C. The Biot number is less than or equal to 0.1.
D. The Biot number is greater than or equal to 1.

Where do you prefer to live?
USA UK Canada ????????
Answer for POINTS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Can someone tell me what car, year, and model this is please

FOR BRAINLIST HELP PLEASE IS A DCP

A- Causes of the 13t Amendment

B- Reasons for Women's Suffrage

C- Reasons for the Freedmen's Bureau

D- Causes of the Plantation System

Name some technical skills that are suitable for school leavers .​