The volume of an ideal gas is increased from 0.6 m3 to 2.4 m3 while maintaining a constant pressure of 1000 Pa (1000 N/m2). Determine, in J, the amount of work done by the gas in this expansion.

Answers

Answer 1

The amount of work done by the gas in the given expansion is 1800 J.

The given parameters;

initial volume of the ideal gas, V₁ = 0.6 m³final volume of the ideal gas, V₂ = 2.4 m³constant pressure of the gas, P = 1000 Pa

The amount of work done by the gas in the given expansion is calculated as follows;

W = PΔV

where;

ΔV is the change in volume of the gas

Substitute the given parameters and solve for the work done;

W = 1000(2.4  -  0.6

W = 1800 J

Thus, the amount of work done by the gas in the given expansion is 1800 J.

Learn more here:https://brainly.com/question/14978695


Related Questions

What will be the current through a resistance of 50Ω if the applied voltage across the resistance is 117V?
Formulas: V=IR, I=V/R, R=V/I
Note: No need to write the unit of your answer.

Answers

2.34 A

Explanation:

[tex]V = IR \Rightarrow I = \dfrac{V}{R} = \dfrac{117\:\text{V}}{50\:Ω} = 2.34\:\text{A}[/tex]

When converted to a household measurement, 9 kilograms is approximately equal to a

Answers

Ificicicucuivvicicicucucucu

Answer:

D) 19.8 lbs

Explanation:

1kg in household measurement is equal to 35.274 ounces. 35.274*9=317.466 ounces.

1kg is also equal to 2.205 lbs. 9*2.205=19.8416

9 kg is also equal to 9000 grams, but grams are not a part of the household measurement system

a) 9000 grams. b) 9000 ounces. c) 19.8 ounces. d) 19.8 pounds.

This leaves us with 19.8 lbs

I NEED A 100% ACCURATE ANSWER FOR THIS QUESTION ASAP NO LINKS !!!
What describes the pressure in a contained fluid?
1: unknown as long as the fluid is contained
2: the same throughout the fluid
3: higher in some places and lower in other places

Answers

Answer:

3) higher in some places nd lower In other places

Explanation:

The pressure in a fluid is given by the law

p = p0 + pgh

where

p0 is the atmospheric pressure

p is the fluid's density

g is the acceleration of gravity

h is the depth at which the pressure is calculated

As we see, the pressure depends on the value of h (depth): therefore, points which are located at more depth experience a larger pressure than points located near the fluid's surface.

A spring of spring constant k = 200 N m−1 is slowly extended from an extension of 3.0 cm to an extension of 5.0 cm. Calculate the work done by the extending force. 60

Answers

Answer:

31

Explanation:

No need

The correct answer is 31 I did it

Suppose a ball is dropped from a building. What is the change of velocity between the first and fifth seconds of its flight

Answers

Answer: 39.2m/s

Explanation:

Due to the free falling body, the acceleration of the ball is 9.8 m/s^2, and its initial velocity is 0 m/s.

V(t) = g*t

The change of velocity from t=1 to t=5:

Delta V = 9.8*(5-1) = 39.2 m/s

HELPPP


Which of the following statements about friction is FALSE .
1 ) Friction involves objects that are in physical contact .
2) Friction is less if surfaces are very smooth .
3 ) Friction is always in the direction of the motion .
4) Friction is caused by the uneven surfaces of touching objects

Answers

Friction is caused by the uneven surfaces of touching objects

Which term describes energy stored in the bonds between atoms?
A. Nuclear energy
B. Chemical energy
O C. Thermal energy
D. Sound energy

Answers

Answer:

B. Chemical energy

Explanation:

chemical energy is the energy stored in the bonds between atoms

A massive launcher sends a projectile vertically upwards from the surface of a planet of mass M and radius R. You may assume that this planet has no atmosphere. Part A If the projectile is launched at the escape speed, how do the magnitudes of its initial KE and gravitational potential energy (GPE) compare

Answers

Answer:

It can be shown that the potential energy of an object at the surface of the planet would be -G M / R if the potential at infinity is chosen to be zero.

Kinetic energy of G M / R would be required for the escape speed of such an object. The total energy in all such cases is zero.

This can easily be seen by considering the speed of an object falling from infinity towards the planet - the total energy will remain zero if it was zero when the object started to fall.

The potential at infinity is set to zero while the kinetic energy will be [tex]\rm \frac{GM}{R}[/tex] and total energy will be zero.

What is escape speed?

Escape speed is the minimum speed required for a free, non-propelled object to escape from the gravitational pull of the main body and reach an infinite distance from it in celestial physics.

It is proven that if the potential at infinity is set to zero, the potential energy of an item on the planet's surface is [tex]\rm \frac{-GM}{R}[/tex].

The escape speed of such an item would necessitate kinetic energy will be [tex]\rm \frac{GM}{R}[/tex]. In all of these circumstances, the total energy is zero.

Consider the speed of an item falling from infinity towards the planet: if the total energy was zero before the thing began to descend, the total energy will stay zero.

Hence the potential at infinity is set to zero while the kinetic energy will be [tex]\rm \frac{GM}{R}[/tex] and total energy will be zero.

To learn more about the escape speed refer to the link;

https://brainly.com/question/14178880

The rocket now has a thruster that malfunctions and is now pushing the rocket in the wrong direction. What is the new net force on the rocket if it is now accelerating at 12mls²??​

Answers

From your previous question

Mass=30kgAcceleration=12m/s^2

[tex]\\ \sf\longmapsto F=ma[/tex]

[tex]\\ \sf\longmapsto F=30(12)[/tex]

[tex]\\ \sf\longmapsto F=360N[/tex]

The gas state of water

Answers

Answer:

The gas state of water is water vapour. It is formed by boiling liquid water or from the sublimation of ice (sublimation is the process of converting a solid to a liquid). Hope this helps!

*Sorry for the bad quality picture!*

A frictionless pendulum with a mass of 0.4 kg and a length of 2.1 m starts at point A, at an angle 0 of 60°. As it swings downward, it passes through point B, which is 30 degrees from equilibrium. What is the kinetic energy of the pendulum at point B?

A) 3.9 J

B) 3.0 J

C) 1.1 J

D) 4.1 J

Answers

The conservation of mechanical energy allows finding the result for the speed of the pendulum when it is at 30º is:

       

The speed is: 3.88 m / s

The conservation of mechanical energy is a theorem of greater importance in physics and ordinary life, it states that if there is no friction force the total mechanistic energy remains constant at all points.

Mechanical energy is the sum of kinetic energy plus all potential energies. In the attachment we see a diagram of the pendulum's movement at the two points of interest.

They indicate that the pendulum is released from an initial angle of θ₁ = 60º, let's find the mechanical energy at that point.

      Em₀ = U = m g h

Where the height is measured from the lowest point of the movement.

      h = L - L cos tea1 = L (1 cos tea1)

The second point of interest occurs for θ₂ = 30º.

At this point part of the energy is indica and part gravitational potential.  

     [tex]Em_f[/tex]  = K + U₂

      [tex]Em_f[/tex] = ½ m v² + m g h ’

There is no friction in the system, therefore mechanical energy is conserved.

       Em₀ = Em₀_f

       mg L (1 - cos θ₁) = ½ m v² + m g L (1 - cos θ₂)

       v² = 2g L (cos θ₂ - cos θ₁)

Let's calculate.

   

       v² = 2 9.8 2.1 (cos 30 - cos 60)

       v² = 41.16 0.366

       v = 3.88 m / s

In conclusion using the conservation of mechanical energy we can find the result for the speed of the pendulum when it is at 30º is:

       

The speed is: 3.88 m / s

Learn more here: brainly.com/question/14688403

Answer:

3.0 J

Explanation:

Just took the test

Based on your observations, what can you say about your prediction in Parts A and B above concerning the potential and kinetic energy?

Answers

Answer:

Explanation:

My perdiction was correct. I predicted in Part A that the Kinetic Energy would increase. In Part B I predicted that the potential energy would decrease due to the kinetic energy increasing.

tính chỉ số ampe kế thay ampe kế bằng vô kế có điện trở rất lớn thì vô kế chỉ bao nhiêu

Answers

Answer:

I don't understand it.....

In 1962 measurements of the magnetic field of a large tornado were made at the Geophysical Observatory in Tulsa, Oklahoma. If the magnitude of the tornado's field was B = 17.50 nT pointing north when the tornado was 9.10 km east of the observatory, what current was carried up or down the funnel of the tornado? Model the vortex as a long, straight wire carrying a current. A (conventional current) flowing ---Direction--- the tornado.

Answers

Answer:

796.25 A

Explanation:

B= (μI)/(2πr)

I= (B*2πr)/(μ)

μ= 4π*10^-7

I= ((17.50*10^-9)(2π)(9.10*10^3)) / (4π*10^-7)

= 796.25 A

A (conventional current) flowing "DOWN" the tornado.

There are 6 foundation of sports and which one you think is the most important?

Answers

I just need the points

Explanation:

But just pick any and say something like "it stans out to me most/more" or "it sounds/looks more intristing to me"

Someone help this is a test and i need to finish this quick i will give brainliest of it lets me

Answers

Sorry, I don't know but I think the correct answer is the first option.

Un avión vuela horizontalmente con una velocidad de 800 km/h y deja caer
un proyectil desde una altura de 500 respecto al suelo. a) ¿Cuánto tiempo
transcurre antes de que el proyectil se impacte en el suelo?; b) ¿Qué distancia
horizontal recorre el proyectil después de iniciar su caída?

Answers

The projectiles launch allows to find the results for the questions of the launch of the bomb are:

     a) The fall time is: t = 10.1 s

     b) The distance traveled is: x = 2.24 10³ m

Projectile launching is an application of kinematics where the acceleration on the x-axis is zero and the acceleration on the y-axis is gravity acceleration.

a) Let's find the time until we reach the ground.

The initial vertical velocity is zero, the initial height is I = 500 m, when reaching the ground its height y = 0.

        [tex]y = y_o + v_o_y - \frac{1}{2} g t^2[/tex]  

        0 = y₀ + 0 - ½ g t²

        t = [tex]\sqrt{\frac{2y_o}{g}[/tex]  

        t = [tex]\sqrt{\frac{2 \ 500}{9.8} }[/tex]  

        t = 10.1 s

b) We look for the horizontal distance traveled.

Let's reduce to the international measurement system (SI).

       v = 800 km / h ([tex]\frac{1000m}{1km}[/tex]) ([tex]\frac{1h}{3600s}[/tex]) = 222.22 m / s

       x = vₓ t

       x = 22.22 10.1

       x = 2.24 10³ m

In conclusion, using the projectile launch relationships, we can find the results for the questions that are:

     a) The fall time is: t = 10.1 s

     b) The distance traveled is: x = 2.24 10³ m

Learn more here: brainly.com/question/6287497

Ex 2) A cannon ball is shot straight up into the air with an initial velocity of 25 m/s[Up).
What is the maximum height of the cannonball?

Answers

Explanation:

The final velocity at the cannon ball's maximum height is zero ([tex]v_y = 0[/tex]). We can use the equation

[tex]v_y^2 = 0 = v_{0y}^2 - 2gy_{max}[/tex]

[tex]\Rightarrow y_{max} = \dfrac{v_{0y}^2}{2g}[/tex]

[tex]y_{max} = \dfrac{(25\:\text{m/s})^2}{2(9.8\:\text{m/s}^2)}[/tex]

[tex]\:\:\:\:\:\:\:=31.9\:\text{m}[/tex]

What is an involuntary and a voluntary muscle action?

Answers

Answer:

Involuntary muscle action are muscles that move WITHOUT conscious control, and voluntary muscle action are muscles that move WITH conscious control.

Explanation:

A example of a involuntary muscle action would be your heart. Your heart is a muscle beats without you thinking about it and is very vital to your body. A example of a voluntary muscle would be the muscles that are attached to your bones and allow you to move your body, and it's voluntary because your body won't move on it's own.

Hope this helps.

HELP! I need some assistance

Answers

Answer:

I'm a Filipino hahahah I'm not

Ex 3) A tennis player lobs the tennis ball up in the air during a serve at a rate 3 m/s.
How long will it take the tennis ball to reach its maximum height?

Answers

Explanation:

s=(v^2-u^2)/2g

=(0-3^2)/2*10

= 0.45m

1) A bowling has a mass of 5 kg and a speed of 8 m/s. What is its momentum?
2) If the bowling ball started from a momentum of O and reached a momentum of 40
kg*m/s in 2 seconds. What is the impulse impacted on the bowling ball?
3) What is the force of impact for the 2 seconds?

Answers

Hgihucycyvyvuvuvuvuvuvuvuvvuvuvuv

A 3000 kg car stops at a red light, and is rear-ended by a 5000 kg truck traveling at 20m/s. In the collision, the two cars stick together. What is the final speed of the two cars just after the collision in m/s (Numeric Answers only)​

Answers

Explanation:

this is actually not as simple as it sounds here.

quite some energy is lost in the deformation of the bodies of car and truck, and it also needs more energy to get a standing object going than to accelerate an already moving object.

but assuming the simple described circumstances, then the energy and impulse of the moving truck of 5000 kg is transferred to a new combined system of car and truck of now 5000 + 3000 = 8000 kg.

so, the 20m/s inertia energy of the truck is now distributed to the truck/car combination.

since the same energy has to move now more mass, it is clear that the combined speed will be lower.

20×5000 = x×8000

20×5 = x×8

x = 100/8 = 12.5 m/s

that is the resulting speed of the combined truck/car object.

A 23 g bullet traveling at 230 m/s penetrates a 2.0 kg block of wood and emerges cleanly at 170 m/s. If the block is stationary on a surface with a coefficient of kinetic friction of 0.15 when hit, how far does it move after the bullet emerges?

Answers

The distance traveled by the wood after the bullet emerges is 0.16 m.

The given parameters;

mass of the bullet, m = 23 g = 0.023 gspeed of the bullet, u = 230 m/smass of the wood, m = 2 kgfinal speed of the bullet, v = 170 m/scoefficient of friction, μ = 0.15

The final velocity of the wood after the bullet hits is calculated as follows;

[tex]m_1u_1 + m_2 u_2 = m_1v_1 + m_2v_2\\\\0.023(230) + 2(0) = 0.023(170) + 2v_2\\\\5.29 = 3.91 + 2v_2\\\\2v_2 = 1.38\\\\v_2 = \frac{1.38}{2} = 0.69 \ m/s[/tex]

The acceleration of the wood is calculated as follows;

[tex]\mu = \frac{a}{g} \\\\a = \mu g\\\\a = 0.15 \times 9.8\\\\a = 1.47 \ m/s^2[/tex]

The distance traveled by the wood after the bullet emerges is calculated as follows;

[tex]v^2 = v_0^2 + 2as\\\\v^2 = 0 + 2as\\\\v^2 = 2as\\\\s = \frac{v^2}{2a} \\\\s = \frac{(0.69)^2}{2(1.47)} \\\\s = 0.16 \ m[/tex]

Thus, the distance traveled by the wood after the bullet emerges is 0.16 m.

Learn more here:https://brainly.com/question/15244782

Computes average speed when a person walk for 1 minute at speed of 1.5 m/s and another 1 minute at speed of 3.5 m/s along a straight road

Answers

Answer:

2.5 m/s

Explanation:

(60*1.5+60*3.5)/120=2.5

or

(1.5+3.5)/2=2.5

4. What is the density of a block with a mass of 36 g and a volume of 9 cm?
O A 45 g/cm3
O B.27 g/cm
O 0.4 g/cm
O D. 0.25 g/cm

Answers

Answer:

0.4 g/cm

Explanation:

density (g cm ³) = mass (g)

÷

volume (cm³)

Answer:

C. 4 g/cm

Explanation:

Use the formula:

density = mass ÷ volume

mass = 36volume = 9

Sub in the values:

density = 36 ÷ 9 = 4 g/cm

Answer = 4 g/cm

ALREADY SOLVED Thank you for looking.

Answers

what nonsense you are say it have been solved when why did you put

Answer:

yes

Explanation:

define potential difference as used in electricity​

Answers

Answer:

Explanation:

Testing answer please do not delete

the diffrence in potential betwen two points that represents the work involved or the energy relesed in the transfe of a unit quantity of electicity from one point to the other

Ex 1) A Major League baseball pitcher throws a baseball straight up into the air and the ball travels for 4
seconds reaching a height of 52 m before returning to the pitchers hand exactly at the height that he released
it. With what velocity does the baseball strike the pitchers hand on the way back down?

Answers

Answer:

52 / 4 = 13 m/s

Explanation:

Car A uses tires for which the coefficient of static friction is 0.384 on a particular unbanked curve. The maximum speed at which the car can negotiate this curve is 16.7 m/s. Car B uses tires for which the coefficient of static friction is 0.809 on the same curve. What is the maximum speed at which car B can negotiate the curve

Answers

Car C would like a summary too
Other Questions
How is aerobic cellular respiration different from fermentation? What is the Benjamin Franklin warning will happen at the end of this excerpt? "Nor Mars his sword nor war's quick fire shall burn/the living record of yourmemory of your memory."This is an example of -AllusionMetaphorPersonificationHyperbole What is 0.00000008 in scientific notation? Solve the math problem why did Columbus refer to native inhabitants as naked people Where in your body do you think cell division is occurring? Pendulum mass is 4 kg. Use your equations for gravitational potential energy and kinetic energy to determine these values based on the data given below. Total energy is the sum of gravitational potential energy and kinetic energy. In this problem, round gravity to: g = 10 m/s2. What were "Hieroglyphics" and what did they preserve? Nhng i din kit xut ca trng phi m nhc c in Vienne v nhng ng gp ca h cho s pht trin m nhc th gii The graph shows the number of servings in different amounts of frozen yogurt listed on a carton. Enter an equation that gives the number of servings y in x pints. Use only decimal form, if necessary.The equation is y = in order for a circuit work there can be no _______ within the circuit? To Label or Not to Label: California Prepares to Vote on Genetically Engineered Foodsby Richard Dahl (excerpt)Although campaigns for and against GE labeling [for genetically engineered foods] in California are focusing heavily on economic impacts, the real debate revolves around a scientific question: Are these foods truly safe or not?I think its fair to say that most scientists think the techniques that are used [to create GE plants] are not inherently dangerous, says Peggy Lemaux, a cooperative extension specialist in the Plant and Microbial Biology Department at the University of California, Berkeley. In fact, in 2010 the European Commission released an analysis of 50 studies conducted on GE foods over the last 25 years and concluded that GE technologies posed no greater risks than conventional breeding technologies....The reason I dont worry about GMOs [genetically modified foods] is not because someone has convinced me with a big study that theyre safe, says Michael Eisen, an associate professor of genetics, genomics, and development at the University of California, Berkeley, and an investigator at the Howard Hughes Medical Institute. Its because when I look at the technology, I understand what this technology is doing. Theyre introducing proteins that have been very well characterized into plants, and I dont see any reason at all to suspect that these are harmful. . . .Some scientists, however, believe questions about the safety of GE foods are far from answered. Doug Gurian-Sherman, senior scientist with the Food and Environment Program at the Union of Concerned Scientists, says the question is not whether theres risk involved in GE foods, but whether its greater than risks posed by conventional foods. Because of the greater capacity to bring unknown quantities into the food supply, Im of the school that says it has somewhat higher potential for risk, he says. Other scientists say no. But I dont think its a settled debate.Hansen responds to claims that theres no evidence of harm from GE foods by saying, Thats just not true. I can show you all kinds of studies in the scientific literature that have . . . raised red flags that need to be followed up on. In one such study, investigators reviewed 19 studies of mammals fed GE soybeans and maize. They found that several convergent data appear to indicate liver and kidney problems as end points of GMO diet effects, with the kidneys more affected in males and the liver more affected in females. The authors, noting the limitations of the 28- and 90-day assays they reviewed, pointed out that chronic toxicity testing is not required for GE foods, but that it should be.3Select the correct answer.Which description provides the best objective summary of the article in the passage?A. The purpose of the article is to tilt the readers opinion against food labeling for genetically engineered food. It presents expert opinion to support the claim that genetically engineered foods are safe and dismisses the opposing arguments.B. The purpose of the article is to tilt the readers opinion in favor of food labeling for genetically engineered food. It refutes claims that genetically engineered foods are safe by using expert opinion to support the opposite claim.C. The article presents a balanced view of the debate about labeling genetically engineered foods. It examines the claim that genetically engineered foods are as safe as organic foods and then examines claims to the contrary.D. The article presents a balanced view of the debate about labeling genetically engineered foods. Its purpose is to demonstrate fallacies in different arguments for and against the claim that genetically engineered foods are safe. If the incorporator makes a serious mistake in the process of incorporation the business, such as not filing the articles of incorporation with the secretary of state, the courts may still recognize the corporation as a(n) _______ corporation. Multiple Choice de facto executory implied de jure What does it mean when anelectromagnetic wave has low energy?A. it has a long wavelength B. It has a short wavelength C.it has a short amplitudeD. It has a high frequency is algae is saprophytic plantyesno Jimin wants to know whether if there is a difference in proportion of people who like mint chocolate chip-flavored ice cream between Americans and Koreans. She takes a random sample of 46 Americans and find that 30 of them like the flavor, and then she takes a random sample of 53 Koreans and find that 24 of them like the flavor. For a 95% confidence interval of the true difference in proportion of people who like this ice cream flavor, what is the margin of error (MOE) (I NEED THE ANSWER FAST PLS) Explain how to use place value and the distributive property to find the product of 828 and 9. (also, please do not give the edge sample answer) i am confused and this is my last test on my khan academy due list "The quotient of five less than a number and 6, is -4."