What is the difference between ode15s and ode45?

Answer: electrostatic force

Explanation:

electrostatic forces pull or push on objects without touching them, which is how when you rub some materials together they can result in something called a 'charge', being moved from point A to point B.

Energy (E) is related to wavelength (λ) and frequency (ν) according to the equation E=hν, where h is Planck’s constant (6.626 × 10-34 J-s).

Wavelength is the distance between two successive peaks or troughs of a wave, such as light, sound, or other forms of energy. It is measured in meters or nanometers and is related to the frequency of the wave, as the frequency is inversely proportional to the wavelength. Wavelength can also be used to describe the physical size of an object, such as a particle or cell.
The equation for calculating wavelength (λ) is λ=c/ν, where c is the speed of light (3.0 × 10⁸ m/s). The equation for calculating frequency (ν) is ν=c/λ. Therefore, the formulas for calculating energy wavelength and frequency are:
Energy (E) = hν
Wavelength (λ) = c/ν
Frequency (ν) = c/λ
To know more about wavelentgh click-
https://brainly.com/question/10750459
#SPJ4

The separation of the plates in this parallel-plate capacitor is approximately 6.49 micrometers.

The separation of the plates in a parallel-plate capacitor can be calculated using the equation:

d = ε0 * ∆V/σ

where d is the separation of the plates, ε0 is the electric constant (also known as the permittivity of free space), ∆V is the potential difference between the plates, and σ is the surface charge density on the plates.

In this case, the potential difference between the plates is given as v = 6.0 V, and the surface charge density on the plates is given as σ = 7.0 nC/m^2. Plugging these values into the equation above, we get:

d = (8.85 x 10^-12 C^2/N*m^2) * (6.0 V) / (7.0 nC/m^2)

This simplifies to:

d = 6.49 x 10^-6 m

To know more about capacitance

https://brainly.com/question/14746225

#SPJ4

(a) The work done by the shot-putter is 313.6 J.

(b) The force exerted by the shot-putter is 627.2 N.

(c) The power used by the shot putter is 7024.6 Watt.

The work done by the shot-putter is equal to the change in the kinetic energy of the shot-put.

W = ΔK.E

W = ¹/₂m(v² - u²)

where;

W = ¹/₂m(v² - 0)

W = ¹/₂mv²

W = ¹/₂(5)(11.2)²

W = 313.6 J

The force exerted by the shot-putter is calculated as follows;

W = Fd

where;

F = W / d

F = ( 313.6 J ) / (0.5 m)

F = 627.2 N

The power used by the shot putter is calculated as follows;

P = Fv

P = (627.2 N) x (11.2 m/s)

P = 7,024.6 Watt

Learn more about work done here: https://brainly.com/question/25816840

#SPJ1

Answer:

B

Explanation:

At highest point gravitational energy is higher. While coming down without paddle it starts to gain heat energy and once it reaches the ground the kinetic energy is higher.

I hope my answer helps you.

To start an object moving, a force must be applied to the object which must be greater than the forces that are acting to keep the object at rest.

The amount of force needed to start an object moving depends on the mass of the object, as well as the type and magnitude of the forces acting on it. For example, it may take more force to start a heavy object moving than a light object, and it may take more force to start an object moving on a rough or slippery surface than on a smooth or sticky surface.

To apply a force to an object, we can push or pull on it, use a lever or other mechanical advantage to amplify the force, or use an external force such as gravity or a motor to move the object. Once the object is moving, it will continue to move unless acted upon by another force.

Learn more about force here:

https://brainly.com/question/12785175

#SPJ4

Frequency, in physics, the number of waves that pass fixed point in unit time; also, the number of cycles or vibrations undergone during one unit of time by a body in periodic motion.

What is frequency?

To know more about frequency, click the link given below:

https://brainly.com/question/30053506

#SPJ4

Your marital status, health information, shopping patterns, financial transactions, income, account balances, criminal history, and level of education are not included in your credit report. Thus, option C is correct.

Your credit report contains personal information, credit account history, credit queries, and public records. These details will be provided to the credit reporting agencies by your creditors and lenders. A significant portion of information is utilized to determine your Scores, which tell prospective lenders how creditworthy you are.

All credit reports contain essentially the same types of information, even if Experian, Equifax, and TransUnion format and publish your information differently.

Therefore, The amount of money in your checking account.

Learn more about credit report here:

https://brainly.com/question/2989702

#SPJ1

From of the longest infrared light through the visible light spectrum to a shortest ultraviolet rays, thermal radiation spans the entire electromagnetic spectrum.

In increasing frequency and decreasing wavelength order, radio waves, microwave, infrared, visible light, ultraviolet radiation, X-rays, gamma rays, and cosmic rays make up the full electromagnetic spectrum.

Thermal radiation is the process of transferring heat through electromagnetic radiation that is produced by thermal motion of matter particles.This electromagnetic radiation is located in the infrared portion of the spectrum, which is invisible to most Earthly bodies.

To know more about  thermal radiation visit:

https://brainly.com/question/24200572

#SPJ4

Based on the given diagram that contains four items with a predefined mass, it is stated that the four items which are: sponge, glass, eraser and steel are submerged in water for 30 minutes, when they are all brough out, the item that would likely have an increase in weight is the sponge.

This refers to the term that is used to describe and define the force exerted by gravity on an object. The gravitational force acting on the item is referred to as weight in several common textbooks. Some people refer to weight as a scalar quantity that measures the gravitational force's strength.

Hence, it can be seen that a sponge is a foamy material that absorbs water, unlike the other materials and this is the material that would feature an increase in weight after being submerged in water for 30 minutes.

Read more about weights here:

https://brainly.com/question/2337612
#SPJ1

Answer:

3*3-४3*74-7%**&-*%३;9८32&*7५३३6

Work done by friction and air resistance -780,000 Joules. Since the work done by the combined forces of friction and air resistance is negative, this means that these forces are doing negative work on the car, which means that they are slowing the car down.

The work done on the car by the force propelling it up the mountain road is given by W = Fd, where F is the force and d is the distance over which the force is applied. Since the force is nonconservative, the work it does on the car is not equal to the change in the car's kinetic energy. Instead, the work done by the force propelling the car is equal to the change in the car's potential energy plus the work done by the nonconservative forces of friction and air resistance.

To find the work done by the combined forces of friction and air resistance, we can use the following equation:

Work done by friction and air resistance = change in kinetic energy - change in potential energy

We can find the change in the car's kinetic energy by subtracting its initial kinetic energy (0 Joules, since it starts from rest) from its final kinetic energy. The final kinetic energy of the car is given by

[tex]KE = \frac{1}{2} mv^2[/tex]

where m is the mass of the car and v is its speed. Plugging in the values, we get:

[tex]KE = (1/2)(1.50 * 103 kg)(27.0 m/s)^2 = 2.16 * 105[/tex] joule

The change in the car's potential energy can be found by subtracting its initial potential energy (which is 0 Joules at sea level) from its final potential energy. The final potential energy of the car is given by

PE = mgh,

where m is the mass of the car, g is the acceleration due to gravity, and h is the height of the car above the ground. Plugging in the values, we get:

PE = (1.50 x 103 kg)(9.8 m/s²)(2.00 x 102 m) = 2.94 x 105 Joules

Substituting these values into the equation above, we get:

Work done by friction and air resistance = (2.16 x 105 Joules) - (2.94 x 105 Joules) = -780,000 Joules

Learn more about work done, here https://brainly.com/question/13662169

#SPJ4

The given question is incomplete, and hence, can not be answered. Still, adding some relevant information for your reference.

What are electromagnetic waves?

Electromagnetic waves, or EM waves, are waves produced by oscillations between electric and magnetic fields. In other words, EM waves consist of oscillating magnetic and electric fields.

Electromagnetic waves are produced when an electric field contacts a magnetic field. Therefore, they are called "electromagnetic waves". The electric and magnetic fields of electromagnetic waves are perpendicular (right angles) to each other. They are also perpendicular to the EM wave direction. The

EM wave propagates in vacuum with a constant velocity of 3.00 x 108 ms-1. They are not deflected by electric or magnetic fields. However, they can exhibit interference or diffraction. Electromagnetic waves penetrate everything, including air, solids, and vacuums. No medium is required to diffuse or move from one place to another.

The given question is incomplete, and hence, can not be answered. Still, adding some relevant information for your reference.

To know more about Electromagnetic waves, visit:

https://brainly.com/question/25847009

#SPJ4

The threshold voltages for NMOS transistors in the 180 nm technology are Vth,r = 0.592 V and Vth,n = 0.068 V.

Leading semiconductor firms, first with TSMC and Fujitsu, then Sony, Toshiba, Intel, AMD, Texas Instruments, and IBM, commercialized the 180 nm process, a MOSFET (CMOS) semiconductor process technology, between 1998 and 2000.

The Threshold voltage at which a sizable current begins to flow from the source to the drain is referred to as the threshold voltage.

A thin inversion layer that separates the insulating from the real body of a transistor is typically used to build a threshold voltage. The region's surface is covered with tiny holes that are positively charged, and when electricity is applied, the particles in these spaces are repelled.

To learn more about threshold voltage from given link

https://brainly.com/question/3157069

#SPJ4

The angle the road should be banked is determined as 2⁰.

The banking angle of the road is calculated by applying the following equation.

tan ( θ ) = v² / rg

where;

The given parameters includes;

radius of the road = 2.3 km = 2,300 m

speed rating of the road = 100 km/hr = 27.78 m/s

tan ( θ ) = v² / rg

tan ( θ ) = (27.78)² / (2,300 x 9.8)

tan ( θ ) = 0.034

θ = arc tan (0.034)

θ = 2⁰

Learn more about banking angle here: https://brainly.com/question/8169892

#SPJ1

The tension in the cord is 39.2 N.

The tension in the cord used in pulling down the solid wooden sphere  is equal to the weight of the solid wooden sphere .

The weight of the sphere is calculated from the density of the solid wooden sphere.

S.G = density of solid wooden sphere / density of liquid

where;

¹/₂ = ρ / (800 kg/m³)

ρ  = ¹/₂ x 800 kg/m³

ρ  = 400 kg/m³

The mass of the solid wooden sphere is calculated as;

m = density x volume

m = 400 kg/m³  x  0.01 m³

m = 4 kg

The tension in the cord is calculated as follows;

T = W = mg

T = 4 kg  x  9.8 m/s²

T = 39.2 N

Thus, the tension in cord is equal to the weight of the solid wooden sphere submerged in the liquid.

Learn more about tension in cord here: https://brainly.com/question/24994188

#SPJ1

Accordingly, the response at A in a vertical direction weight is   W(2cosϕsinθ−sinϕcosθ)/2sin(θ−ϕ).

If you hang the wire from the ceiling while placing a weight on the lower end, it will sag. By dividing the length change by the starting length, the strain in the wire may be computed. By dividing the weight suspended from the wire by its cross-sectional area, the tensile tension in the wire is determined. Stress and strain have a defined ratio.

Modulus is a fundamental characteristic of industrial yarn and thread for wire and cable, especially aramid yarns (fiber elasticity). The relationship between strain (the ratio of deformation over initial length along an axis) and stress (force per unit area along that axis) is referred to as modulus.

In conclusion, cross-linking improved elastic modulus, decreased strain to failure, and had negligible effect on collagen fracture stress in the current experimental design.

The questions is incomplete I answered it in general way

The uniform beam has a weight W and length l and is supported by a pin at A and a cable BC. (Figure 1) Determine the horizontal and vertical components of reaction at A. Express your answers in terms of some or all of the variables W, l, phi and theta. Enter your answers separated by a comma.

To know more about weight

https://brainly.com/question/29255653

#SPJ4

Voltmeters are typically connected in parallel because they have high resistance, while ammeters are typically connected in series to measure current since they have low resistance and the voltage drop would be minimal.

For more information on ammeter kindly visit to

https://brainly.com/question/18404570

#SPJ4

The required speed Vf of the block at this new position 1/2KX²= 1/2KXf ² + 1/2Vf m².

In physics, the kinetic energy of an object is the energy it has due to its motion. It is defined as the work required to accelerate a body of specified mass from rest to a specified velocity. After the body acquires this energy during acceleration, it retains this kinetic energy as long as the velocity does not change. The same work is done when the body slows down from its current speed to rest. Formally, kinetic energy is any term in the Lagrange of a system that includes the time derivative.

In this problem, neglecting friction force, there are two energies at work viz. Potential energy of spring and kinetic energy of spring mass system.

Initially the spring is compressed to  length from the equilibrium position, therefore, initially,

Potential energy= 1/2KX²

(Because potential energy of spring= 1/2×(spring constant)×(compression)²)

At this instance system is at rest, therefore, kinetic energy=1/2mv²=0.

So total initial energy= K.E. + P.E. = 1/2KX²   -(1)

Now in the 2nd instant, spring is compressed to  length from equilibrium, therefore, P.E.=1/2K ²

and velocity=  here,

Therefore, kinetic energy= 1/2 mv²

So total energy= 1/2K ² + 1/2 m²   -(2)

From conversation of energy theorem, (1) and (2) should be equal(Neglecting friction, remember)

Therefore, the correct answer is:  1/2KX²= 1/2KXf ² + 1/2Vf m²

To know more about kinetic energy, visit:

brainly.com/question/8101588

#SPJ4

The magnitude of the normal force acting on the vehicle in mars is 2,220 N

The mass of the vehicle = 600 kg

The speed at which the space vehicle travels = 4.8 m/s

The gravitational field strength = 3.7 N/kg

The magnitude of the force acting on the vehicle can be found using the formula,

                  F = mg

where F is the force acting on the vehicle

          m is the mass of the vehicle

          g is the gravitational strength.

Let us substitute the known values in the above equation, we get

               F = 600 x 3.7

                  = 2,220 N

Therefore, the force acting on the vehicle is 2,220 N

Learn more about the gravitational field strength in

https://brainly.com/question/18511078

#SPJ4

The maximum amount of weight that we can load on a vehicle is known as maximum loading capacity.

The maximum loading capacity of any vehicle can be define as that maximum value of the weight of the body that we can load on the vehicle without damaging any part of the vehicle.

The maximum loading capacity of the vehicle is decided by doing certain experiments and observation by the makers and the manufacturers of the parts of the vehicle.

To avoid accidents and unfortunate events the maximum loading capacity is always higher than the prescribed limit of weight for the vehicle.

To know more about loading capacity, visit,

https://brainly.com/question/14645317

#SPJ4

The only true statement about the toy car is " the toy does not approach the spring".

option A is the correct answer.

The acceleration of the car is calculated by applying Newton's second law of motion, which states that the force applied to an object is directly proportional to the product of mass and acceleration of the object.

F - Ff = 0

F = Ff

ma = μmg

a = μg

where;

a = 0.14 x 9.8 m/s².

a = 1.37 m/s²

The distance traveled by the car before stopping is calculated as follows;

v² = u² - 2as

where;

when the car stop's the final velocity, v = 0

0 = u² - 2as

2as = u²

s = u²/2a

s = ( 2² ) / ( 2 x 1.37 )

s = 1.5 m

Thus, the final distance travelled by the car is less than 3 m, hence the car did not come in contact with spring.

Learn more about distance travelled here: https://brainly.com/question/24283318

#SPJ1

if an object is placed beyond the focal length of a converging len, the image will be real smaller image or real and bigger image depending on the position.

We have four positions of object in front of a converging lens, accordingly there are three types of images formed.

1) When object is placed at infinity - image is real and tiny sized. This image is formed at the focus.

2) when object is placed beyond 2F - image is real and smaller than object.

3) When object is placed at 2F - image is real and equal in size to object.

4) when object is placed between 2F and F - image is real and bigger than object.

A converging lens is a convex lens which converges all the rays coming parallel to the principal axis at a point on the principal axis, called focus.

To know more about converging lens here

brainly.com/question/28348284

#SPJ4

There are two bromide ions are required for every magnesium ion, so, magnesium bromide has a 2.

The chemical formula of magnesium bromide is [tex]MgBr_2[/tex]

As we know, the atomic number of magnesium is 12, while the atomic number of bromine is 35.

So, the electron distribution of Mg will be - 2,8,2

So, Mg needs to release its 2 electrons to complete its octet.

The electronic configuration of Br will be [tex]1s^2, 2s^2, 2p^6, 3s^2, 3p^6, 4s^2, 3d^{10}, 4p^5.[/tex]

Here, the valence electrons are in the 4s and 4p orbitals giving Bromine 7 valence electrons.

So, bromine needs one electron to complete its octet.

From above we can conclude that,

For compensating 2 electrons of Mg, 2 atoms of Bromine is required.

For more questions on ions

https://brainly.com/question/28203551

#SPJ4

Location of the ball is top of the circle and acceleration is 3g.

Since tension force is more, surely ball is having net force upward and hence, the location of the ball in this case is top of the circle.

Any object that moves in a circle has an acceleration vector towards the center of that circle. This is known as Centripetal acceleration.

total force/ net force when ball is top of the circle is sum of tension force and gravity force.

[tex]F_{net[/tex] = T + mg

Because of this net force, there is centripetal acceleration towards the center.

so, T + mg = ma

2mg + mg = ma

3mg = ma

a = 3 × force of gravity

To know more about centripetal acceleration here

brainly.com/question/11324711

#SPJ4

The capacity plate tells us about the maximum load or the maximum number  of people that can be carried by a vehicle.

In boats, the maximum load is measured by the capacity plate Quizlet. The maximum load for a particular region is issued by the authority of that region, which is strictly mandatory to follow. Any violation can lead to strict punishment. Load limit can be calculated by subtracting curb weight from GVWR.

Load limit= GVWR- curb weight

By staying within the load limit one can increase the life of a vehicle also. It is also for human safety purposes.

Learn more about load limit:

https://brainly.com/question/14747975

#SPJ4

magnitude of the induced current        

where  I = 0.5A

 Briefing

Knowing that the formula for magnetic flux is = NBA

Here, N is the number of turns,

B is the magnetic field,

and A is the area of the loop.

Knowing that the coil's EMF will be induced by the rate of change in magnetic flux,

we may calculate it as EMF = NA db/dt.

To find the induced EMF,

we now plug in all values.EMF = 0.2

voltageTherefore, according to Ohm's rule,

Current = EMF/Resistance I = 0.2/0.40.

Visit this link to learn more about the Magnetic field:  

https://brainly.com/question/23096032

#SPJ4

The incentive theory says people are "pulled" by external stimuli to act a certain way.

Humans have both main and secondary needs that must be met in order for them to feel needed. These requirements naturally nudge a person in that direction. Hunger, thirst, and a desire for sexual activity are examples of fundamental wants. Secondary needs, on the other hand, are those that depend on advantages, with financial requirements serving as the finest illustration.

According to incentive theories, conduct is driven by the "pull" of external objectives like rewards, money, or recognition. It's simple to imagine a variety of circumstances in which a specific objective, like a job promotion, can act as an outside incentive to encourage certain actions.

To know more about incentive theory

https://brainly.com/question/29672711

#SPJ4

Answer:

bouncing

Explanation:

The greater efficiency achieved with the curved blades of a pelton wheel is due to bouncing.