Answers
Answer:
d
Explanation:
Related Questions
An old shade-tree mechanic trick for removing a stubborn bolt is to slip a long pipe over the handle of the wrench, then apply a force to the end of the pipe opposite the bolt.
Why is this effective? What problems might this technique cause?
Answers
Answer: long pipe is used to increase torque and reduce force needed.
Explanation: A torque is needed to open bolt. torque = F·r, if
R increases, Force F needed to open bold is smaller.
Problem is a worn bolt may break down. It sometimes I send useful to heat bolt instead using too much power.
a boy cycles continuously through a distance of 1.0 km in 5 minutes calculate its average speed
Answers
Answer:
0.2 km/minute or 12 km/h
Explanation:
All you have to do is divide distance by time to find the speed. 1/5 km/min is the speed into which we simplify to 0.2 km/min. I then multiplied by 60(numerator and denominator) since there are 60 minutes in an hour to get 12 km/h.
assume the femur has a diameter of 3.0cm and a hollow center of 0.8cm diameter and a length of 50cm.if it is supporting a load of 600N/,what is the stress in the femur? How much will it be shortened by this load?Take the young's modulus for the femur bone as 16 × 10^9N/m²
Answers
Answer:
tbh i think hes right
Explanation:
The femur would be shortened by 0.0434 cm by a load of 600N.
What is pressure?The total applied force per unit of area is known as the pressure.
The pressure depends both on externally applied force as well the area on which it is applied.
The mathematical expression for the pressure
Pressure = Force /Area
As given in the problem assume the femur has a diameter of 3.0cm and a hollow center of 0.8cm diameter and a length of 50cm.if it is supporting a load of 600N,
The stress in the femur = force /area
=600 / π(.004²-.0015²)
= 13.89 ×10⁶ Pa
The length reduced by the load = PL/AE
= 13.89 ×10⁶ ×50/ 16 × 10⁹ cm
=0.0434 cm
The femur would be shortened by 0.0434 cm by a load of 600N.
Learn more about pressure here,
brainly.com/question/28012687
#SPJ2
Your car gets a flat! You go from 90 kilometers per hour to a stop in 6 seconds. What is your rate of deceleration?
Answers
Answer:
The rate of deceleration is 15 km/h^2.
Explanation:
Since the car comes in 90km/h, it will need deceleration for 15 km/h for 6 seconds to finally stop the car. 15*6=90
a horizontal 4-cm-diameter water jet with a velocity of 18 m/s. He impinges the jet normally upon a vertical plate of mass 750 kg. The plate rides on a nearly frictionless track and is initially stationary. When the jet strikes the plate, the plate begins to move in the direction of the jet. The water always splatters in the plane of the retreating plate. Determine (a)the acceleration of the plate when the jet first strikes it (time
Answers
Answer:
0.5429 m/s^2
Explanation:
velocity of waterjet = 18 m/s
diameter of water jet ( d ) = 4 cm = 0.04 m
mass of vertical plate(m) = 750 kg
Determine the acceleration of plate when the jet first strikes ( i.e. t = 0 )
first we will determine the impact force
F = β*A*V^2 ----- ( 1 )
where ; β = 1000 kg/m^3 , A = π/4 * d^2 , V = 18 m/s
input values into equation 1
F = 407.15 N
finally determine the acceleration at t = 0
F = m*a
a = F / m = 407.15 / 750 = 0.5429 m/s^2
Using a Boltzmann distribution, find the fraction of atoms in the excited state versus the ground state (i.e. the relative population) in a plasma source and a flame source. Assume that the lowest energy of a sodium atom lies at 3.371x10-19 J above the ground state, the degeneracy of the excited state is 2, whereas that of the ground state is 1, and the temperature of the flame is 3000 K and 10,000 K for plasma.
Answers
Answer:
0.174 plasma
[tex]$5.85 \times 10^{-4}$[/tex] flame
Explanation:
Given :
Energy :
[tex]$\Delta E=3.371 \times 10^{-19} $[/tex] J per atom
[tex]$g^*=2$[/tex] (degenraci of excited state)
g = 1 (degenraci of excited state)
Boltzmann Distribution
[tex]$\frac{N^*}{N}=\frac{g^*}{g}e^{-\frac{\Delta E}{kT}}$[/tex]
where,
[tex]$N^*$[/tex] = atoms in excited state
N = atoms in lower energy level
k = [tex]$1.38 \times 10^{-23}$[/tex] J/K
Therefore,
Relative population in plasma
T = 10,000 K
[tex]$\frac{N^*}{N}=\frac{g^*}{g}e^{-\frac{\Delta E}{kT}}$[/tex]
[tex]$\frac{N^*}{N}=\frac{2}{1}e^{-\frac{-3.37\times 10^{-19}}{1.38 \times 10^{-23} \times 10000}}$[/tex]
[tex]$\frac{N^*}{N}=2 \times e^{-2.44275}$[/tex]
[tex]$\frac{N^*}{N}=2 \times 0.8692$[/tex]
[tex]$\frac{N^*}{N}=0.1738$[/tex]
Relative population in flame
T = 3000
[tex]$\frac{N^*}{N}=\frac{g^*}{g}e^{-\frac{\Delta E}{kT}}$[/tex]
[tex]$\frac{N^*}{N}=\frac{2}{1}e^{-\frac{-3.371\times 10^{-19}}{1.38 \times 10^{-23} \times 3000}}$[/tex]
[tex]$\frac{N^*}{N}=2 \times e^{-8.1425}$[/tex]
[tex]$\frac{N^*}{N}=2 \times 2.9090 \times 10^{-4}$[/tex]
[tex]$\frac{N^*}{N}=5.85 \times 10^{-4}$[/tex]
What is the rate of flow of electric charge around a circuit
Answers
Answer:
Current
Explanation:
hope it helps and your day will be full of happiness
What is the wavelength associated with 0.113kg ball traveling with velocity of 43 m/s?
Answers
Answer:
Wavelength = 1.36 * 10^{-34} meters
Explanation:
Given the following data;
Mass = 0.113 kg
Velocity = 43 m/s
To find the wavelength, we would use the De Broglie's wave equation.
Mathematically, it is given by the formula;
[tex] Wavelength = \frac {h}{mv} [/tex]
Where;
h represents Planck’s constant.
m represents the mass of the particle.
v represents the velocity of the particle.
We know that Planck’s constant = 6.6262 * 10^{-34} Js
Substituting into the formula, we have;
[tex] Wavelength = \frac {6.6262 * 10^{-34}}{0.113*43} [/tex]
[tex] Wavelength = \frac {6.6262 * 10^{-34}}{4.859} [/tex]
Wavelength = 1.36 * 10^{-34} meters
After graduation, you face a choice. You can work for a multinational consulting firm and earn a starting salary (including benefits) of $40,000, or you can start your own consulting firm using $5,000 of your own savings. If you keep your money in a savings account, you can earn an interest rate of 7 percent. You choose to start your own consulting firm. At the end of the first year, you add up all of your expenses and revenues. Your expenses include $14,000 for rent, $1,000 for office supplies, $24,000 for labor, and $4,500 for telephone expenses. After operating your consulting firm for a year, your total revenues are $88,000.
Required:
What are your total explicit cost and total implicit costs?
Answers
Answer:
Explanation:
Money is used to cover the explicit cost. They're what we're used to seeing, and they're easy to identify. There are several classifications for explicit costs; we can distinguish between fixed and variable costs, as well as direct and indirect costs. Raw materials, manpower, indirect production costs, and so on are all factors that contribute to its expense.
The opportunity cost of using a resource is the amount of money paying for it that might have been used on something else.
Alternative benefit options or money that we miss earning by doing such business acts are referred to as opportunity costs.
When a corporation foregoes an alternative action but does not make a bill, it incurs implicit costs. These are a company's hidden costs:
1. The use of the firm's own funds (money or assets).
2. The owner's capital, savings, and financial services are used.
From the given information:
The total explicit cost = Rent + office supplies + office staff + telephone expense
=$( 14000 + 1000 + 24000 + 4500)
= $43500
The total implicit cost = forgone salary + forgone interest
= $40000 + 7% of $5000
= $40000 + 350
=$40350
What kind of force allows a navigational compass to work?
Answers
Answer: Magnetic Fields
Explanation: A Compass works by detecting the earth's magnetic fields. The earth has a iron core that is part liquid and part solid crystal due to gravitational pressure.
BRAINLIEST PLEASE HELP ASAP DO NOT ANSWER UNLESS YOU KNOW AND DON'T GIVE ME A LINK OR I WILL REPORT YOU
1. Explain what type of lever is a baseball bat and why the bat is that type of lever in relation to the input force, output force, and fulcrum.
2. Explain for which class of lever is the output force always greater than the input force.
3. Explain for which class of lever is the output force always less than the input force.
4. Use the law of conservation of energy to explain why in a second class lever the distance over which the input force is applied is always greater than the distance over which the output force is applied.
5. A lever has an IMA of 4. If the length of the length of the input arm is 1.0 meter, what is the length of the output arm.
Answers
Answer:
In a third class lever, the effort is located between the load and the fulcrum. ... If the fulcrum is closer to the effort, then the load will move a greater distance. A pair of tweezers, swinging a baseball bat or using your arm to lift something are examples of third class levers.
Explanation:
For your answer to this problem, just type in the numerical magnitude of the momentum - no units.
An object with a mass M and a velocity v has a momentum of 15 kg•m/s. An object with a mass of 2M and 4v would have a momentum of kg•m/s
Answers
Answer:
120 kg•m/s.
Explanation:
From the question given above, the following data were obtained:
Case 1
Mass of object = M
Velocity of object = V
Momentum = 15 kg•m/s
Case 2
Mass of object = 2M
Velocity of object = 4V
Momentum = ?
Momentum is defined as follow:
Momentum = mass × velocity
The momentum of object in case 2 can be obtained as follow:
From case 1
Momentum = mass × velocity
15 = M × V
15 = MV ....... (1)
From case 2:
Momentum = mass × velocity
Momentum = 2M × 4V
Momentum = 8MV ....... (2)
Finally , substitute the value of MV in equation 1 into equation 2.
Momentum = 8MV
MV = 15
Momentum = 8 × 15
Momentum = 120 kg•m/s
Therefore, an object with a mass of 2M and 4V would have a momentum of 120 kg•m/s
An open organ pipe emits E (330 Hz ) when the temperature is 26 ∘C. The speed of sound in air is v≈(331+0.60T)m/s, where T is the temperature in ∘C. Determine the length of the pipe.
Answers
Answer:
0.525 m
Explanation:
From the question,
In an open pipe,
v = λf................... Equation 1
Where v = speed of sound in the pipe, f = frequency, λ = wave length.
But,
λ = 2l................ Equation 2
Where l = length of the pipe
Substitute equation 2 into equation 1
v = 2lf.............. Equation 3
make l the subject of the equation
l = v/2f............. Equation 4
Given:
v ≈ (331+0.60T) m/s at T = 26°C
v ≈ (331+0.60×26) ≈ 346.6 m/s
f = 330 Hz.
Substitute these values into equation 4
l = 346.6/(2×330)
l = 346.6/660
l = 0.525 m
Hence the length of the pipe is 0.525 m
what is a magnetic flux thru closed surface
Answers
An air-filled pipe is found to have successive harmonics at 980 Hz , 1260 Hz , and 1540 Hz . It is unknown whether harmonics below 980 Hz and above 1540 Hz exist in the pipe. What is the length of the pipe
Answers
Answer:
L = 0.7 m
Explanation:
This is a resonance exercise, in this case the air-filled pipe is open at both ends, therefore we have bellies at these points.
λ / 2 = L 1st harmonic
λ = L 2nd harmonic
λ = 2L / 3 3rd harmonic
λ = 2L / n n -th harmonic
the speed of sound is related to wavelength and frequencies
v =λ f
f = v /λ
we substitute
f = v n / 2L
the speed of sound in air is v = 343 m / s
suppose that the frequency of f = 980Hz occurs in harmonic n
f₁ = v n / 2L
f₂ = v (n + 1) / 2L
f₃ = v (n + 2) / 2L
we substitute the values
2 980/343 = n / L
2 1260/343 = (n + 1) / L
2 1540/343 = (n + 2) / L
we have three equations, let's use the first two
5.714 = n / L
7.347 = (n + 1) / L
we solve for L and match the expressions
n / 5,714 = (n + 1) / 7,347
7,347 n = 5,714 (n + 1)
n (7,347 -5,714) = 5,714
n = 5,714 / 1,633
n = 3.5
as the number n must be integers n = 4 we substitute in the first equation
L = n / 5,714
L = 0.7 m
state and explain newton second law of motion also describe the concept of force, represent it quantiatively and derive the unit of force
this is a long question only answer if you know how to solve it you will be REWARDED with points
Answers
Explanation:
Newton's second law of motion states F=ma which means force is equal to mass multiplied by acceleration which in simple terms means If you give mass force it will accelerate the concept of force in physics is any interaction that when unopposed will change the motion of an object.
In the process of changing a flat tire, a motorist uses a hydraulic jack. She begins by applying a force of 58 N to the input piston, which has a radius r1. As a result, the output plunger, which has a radius r2, applies a force to the car. The ratio r2/r1 has a value of 8.2. Ignore the height difference between the input piston and output plunger and determine the force that the output plunger applies to the car.
Answers
Answer:
The correct answer is "3899.92 N".
Explanation:
The given values are:
Force,
[tex]F_{app}=58 N[/tex]
Ratio,
[tex]\frac{R_2}{R_1}=8.2[/tex]
As we know,
Area, [tex]A=\pi r^2[/tex]
or,
⇒ [tex]\frac{F_2}{F_1} =\frac{A_2}{A_1}[/tex]
On substituting the value of "A", we get
⇒ [tex]\frac{F_2}{F_1} =\frac{\pi r_2^2}{\pi r_1^2}[/tex]
⇒ [tex]\frac{F_2}{F_1} =\frac{r_2^2}{r_1^2}[/tex]
On applying cross-multiplication, we get
⇒ [tex]F_2=F_1\times (\frac{r_2}{r_1} )^2[/tex]
On substituting the given values, we get
⇒ [tex]=58\times (8.2)^2[/tex]
⇒ [tex]=58\times 67.2[/tex]
⇒ [tex]=3899.92 \ N[/tex]
Find the current passing through each of the 3 resistors connected parallel to each other as shown in the figure (i1, i2, I3). Show your actions clearly.
Answers
Answer:
I1 = ε/R1
I2 = ε/R2
I3 = ε/R3
Explanation:
From the image, we see that the resistors are connected in parallel. This means that the voltage passing through them is the same.
Now, formula for current is; I = V/R
In this case, V which is voltage is denoted by ε.
Thus;
I1 = ε/R1
I2 = ε/R2
I3 = ε/R3
Two loudspeakers placed 6.0 m apart are driven in phase by an audio oscillator whose frequency range is 2193 Hz to 2967 Hz. A point P is located 4.4 m from one loudspeaker and 3.6 m from the other. The speed of sound is 344 m/s. The frequency produced by the oscillator, for which constructive interference of sound occurs at point P, is closest to
Answers
Answer:
"2580 Hz" is the correct solution.
Explanation:
According to the question,
The path difference,
= [tex]4.4 - 3.6[/tex]
= [tex]0.80 \ m[/tex]
Speed,
= 344 m/s
For constructive interference,
⇒ [tex]Path \ difference =n\times \frac{Speed}{frequency}[/tex]
On substituting the values, we get
⇒ [tex]0.80=n\times \frac{344}{frequency}[/tex]
⇒ [tex]frequency=n\times 430[/tex]
⇒ [tex]n=\frac{frequency}{430}[/tex]
If the frequency range is,
f = 2193,
⇒ [tex]n=\frac{2193}{430}[/tex]
[tex]=5.1[/tex]
If the frequency range is,
f = 2967,
⇒ [tex]n=\frac{2967}{430}[/tex]
[tex]=6.9[/tex]
hence,
For n = 6, the frequency will be:
⇒ [tex]Frequency=n\times 430[/tex]
[tex]=6\times 430[/tex]
[tex]=2580 \ Hz[/tex]
what can i use to curl my eyelashes other den mascara and eyelash curler
Answers
Explanation:
a hot toothbrush. ......lol
Two children are balanced on a seesaw that has a mass of 18.0 kg. The first child has a mass of 26.0 kg and sits 1.60 m from the pivot. The center of mass of the seesaw is 0.133 m from the pivot (on the side of the first child). (a) If the second child has a mass of 34.4 kg, how far (in m) is she from the pivot
Answers
Answer:
1.28 m
Explanation:
As shown in the diagram attached,
According to the principle of moment,
For a body at equilibrium,
Sum of clockwise moment = sum of anticlockwise moment.
Taking moment about the pivot,
W₁(1.6)+W(0.133) = W₂(x)............... Equation 1
Where W₁ = Weight of the first child, Wₓ = Weight of the seesaw, W₂ = weight of the second child, x = distance of the second child from the pivot.
But,
W = mg
Where g = 9.8 m/s², m = mass of the body
Therefore,
W₁ = 26×9.8 = 254.8 N,
Wₓ = 18×9.8 = 176.4 N
W₂ = 34.4×9.8 = 337.12 N
Substitute these values into equation 1
(254.8×1.6)+(176.4×0.133) = 337.12(x)
407.68+23.4612 = 337.12x
337.12x = 431.1412
x = 431.1412/337.12
x = 1.2789
x ≈ 1.28 m
An object that weighs 20 N encounters 20 N of air resistance. What is the acceleration in the y direction?
Answers
Answer:
Explanation:
F=ma.
a=m÷fcos 0
why all monosacharides and dissacharides are soluble in waters
Answers
How would doubling the mass of Earth affect the gravity we experience?
Answers
Explanation:
if the mass or both of the objects is doubled, then the force of gravity between them is quadrupled and so on. Since gravayional force is inversely proportional to the square of separation distance between two interacting objects, more separation distance will result in weaker gravitational forces.
A radial saw has a blade with a 9-in. radius. Suppose that the blade spins at 1000 rpm. (a) Find the angular speed of the blade in rad/min. Incorrect: Your answer is incorrect. webMathematica generated answer key rad/min (b) Find the linear speed of the sawteeth in ft/s. Incorrect: Your answer is incorrect. webMathematica generated answer key ft/
Answers
Answer:
The angular speed of the blade is of 166.67 rad/min
If a radial saw has a blade with a 9-in. radius. Suppose that the blade spins at 1000 rpm then the angular speed of the blade would be 104.72 rad/seconds.
What is speed?
The total distance covered by any object per unit of time is known as speed. It depends only on the magnitude of the moving object. The unit of speed is a meter/second. The generally considered unit for speed is a meter per second.
The mathematical expression for speed is given by
speed = total distance /Total time
As given in the problem If a radial saw has a blade with a 9-in. radius. Suppose that the blade spins at 1000 rpm then we have to find the angular speed of the blade,
the angular speed of the blade (ω) = 2πN/60
=2×π×1000/60
= 104.72 rad/seconds
Thus, the angular speed of the radial saw would be 104.72 rad/seconds
To learn more about speed from here,refer to the link;
https://brainly.com/question/7359669
#SPJ2
In what way would a digital thermometer be preferable to those from a liquid-based thermometer?
Answers
A uniform metre rule of mass 100g balance the 40cm mark when a mass x is placed at the 20cm mark
what is the value of x
Answers
Answer:
X = 50 g
Explanation:
Please see attached photo for explanation.
From the attached photo,
Anticlock–wise moment = X × 20
Clockwise moment = 100 × 10
Anticlock–wise moment = clockwise moment
X × 20 = 100 × 10
X × 20 = 1000
Divide both side by 20
X = 1000 / 20
X = 50 g
Therefore, the value of X is 50 g
why is it important to know all about recreational activities?
Answers
Answer:
It's important
Explanation:
Mental wellness is critical to overall physical health. Participating in recreational activities helps manage stress. Taking time to nurture oneself provides a sense of balance and self-esteem, which can directly reduce anxiety and depression.
Answer:
Mental wellness is critical to overall physical health. Participating in recreational activities helps manage stress. Taking time to nurture oneself provides a sense of balance and self-esteem, which can directly reduce anxiety and depression.
Explanation:
To decrease the angle between the anterior surface of the foot and anterior surface of the lower leg is described as:
Answers
Answer:
dorsiflexion
Explanation:
To decrease the angle between the anterior surface of the foot and anterior surface of the lower leg is described as: dorsiflexion
Answer:
dorsiflexion
Explanation:
Hope this helps
What is the resistance of a 15 ampere current with 8 volts of potential difference?
Answers
Answer:
Resistance in circuit = 0.53 ohm (Approx.)
Explanation:
Given:
Flow of current in circuit = 15 amp
Potential difference = 8 Volts
Find:
Resistance in circuit
Computation:
In an electrical system, resistance is a stopper of a material to electric current.
Resistance in circuit = Potential difference / Flow of current in circuit
Resistance in circuit = 8 / 15
Resistance in circuit = 0.53 ohm (Approx.)