Answer:
1/4πε₀[Hx/ (√x² + b²)^3/2]i.
Explanation:
So, without mincing words let's dive straight into the solution to the question above. There is need to determine the electric field on-axis of a uniformly-charged disk sitting.
The electric field in the x-component, dεₓ = 1/4πε₀[H/ x² + b²] cos .
Thus, the total electric field in the x-component, εₓ = 1/4πε₀ [ xdH/ (x^2 + b^2)^3/2.
Therefore, the electric field = 1/4πε₀ [ xdH/ (x^2 + b^2)^3/2i.
Where x=0
Let's say you were using a single-pulley system to lift a flag up a flagpole. If you wanted to raise the flag 10 meters into the air, how far would you have to move the rope?
a. 5 meters
b. 10 meters
c. 20 meters
d. 50 meters
Answer:
b. 10 meters
Explanation:
In a single pulley , which is a lever , velocity ratio is one . In other words , velocity of load is equal to velocity of effort . The load shifts by the same distance as the force or effort moves . The only advantage of this pulley is that direction of force is reversed .
Hence to raise a flag by 10 m , rope would have to move by 10 m .
Plz help this is so confusing
The correct answer is 5 km/h
Explanation:
The speed at which the duck travels can be found by using the equation that is given (speed= distance/ time). The first step to do this is to replace distance and time using the values given. Here is the process:
speed = distance / time
speed = 10 km / 2 hours
Now, solve this equation
speed = 10 km/ 2 hours
10 / 2 or 10 divided 2 = 5
Finally, use the units, in this case, the correct units are km/h
Block X and block Y travel toward each other along a horizontal surface with block X traveling in the positive direction. Block X has a mass of 4kg and a speed of 2ms. Block Y has a mass of 1kg and a speed of 1 ms. A completely inelastic collision occurs in which momentum is conserved. What is the approximate speed of block X after the collision
Answer:
v = 1.4 m / s
Explanation:
To solve this problem we use the law of conservation of momentum, for this we define a system formed by the two blocks in such a way that the force during the collision have been internal
initial instant. Just before the crash
p₀ = M v₁ - m v₂
final instant. Right after the crash
p_f = (M + m) v
the moment is preserved
p₀ = p_f
M v₁ - m v₂ = (M + m) v
v = [tex]\frac{1}{M+m}[/tex] (M v₁ - mv₂)
let's calculate
v = [tex]\frac{1}{4+1}[/tex] (4 2 - 1 1)
v = 1.4 m / s
in the same direction as the largest block (M)
The approximate speed of block X after the collision is 1.4 m/s.
Given information:
Block X and block Y travel toward each other along a horizontal surface with block X traveling in the positive direction.
Block X has a mass of [tex]m_1=[/tex] 4 kg and a speed of [tex]u_1=[/tex] 2 m/s.
Block Y has a mass of [tex]m_2=[/tex] 1 kg and a speed of [tex]u_2=[/tex] -1 m/s.
The collision between them is perfectly inelastic. So, the final velocity of both the objects will be the same.
The momentum of the system will be conserved. Let v be the final velocity of both the blocks.
The final velocity v can be calculated as,
[tex]m_1u_1+m_2u_2=(m_1+m_2)v\\4\times 2-1\times1=(4+1)v\\5v=7\\v=1.4\rm\;m/s[/tex]
Therefore, the approximate speed of block X after the collision is 1.4 m/s.
For more details about collision, refer to the link:
https://brainly.com/question/12941951
To review the solution to a similar problem, consult Interactive Solution 1.43. The magnitude of a force vector is 87.4 newtons (N). The x component of this vector is directed along the x axis and has a magnitude of 72.1 N. The y component points along the y axis. (a) Find the angle between and the x axis. (b) Find the component of along the y axis.
Answer:
(a) 34.4°
(b) 49.4 N
Explanation:
(a) From the diagram,
Amgle between the x axis can be calculated as,
cosΘ = adjacent/hypoteneous
cosΘ = 72.1/87.4
cosΘ = 0.8249
Θ = cos⁻¹(0.8249)
Θ = 34.4°.
Hence the angle between the x axis is 34.4°
(b) To find the component along the y axis we make use of pythagoras theorem.
a² = b²+c²................... Equation 1
Where a = 87.4 N, b = 72.1 N, c = y.
Substitute these values into equation 1
87.4² = 72.1² + y²
y² = 87.4²-72.1²
y² = 2440.35
y = √(2440.35)
y = 49.4 N
Artificial satellites in space can help you find locations on
Earth. True or false?
What is the strength of an electric field that will put a force of
1.28 x 10-15 N on a proton?
Answer: E = 7,490.6 N/C
Explanation:
If we have a field E, and a particle with a charge q, the force that the particle experiences is:
F = E*q
In this case, we know that the force is:
F = 1.2*10^(-15) N
And we know that the particle is a proton, where the charge of a proton is:
q = 1.602*10^(-19) C
Then we can replace these two values in the equation to get:
1.2*10^(-15) N = E*1.602*10^(-19) C
We just need to isolate E.
(1.2*10^(-15) N)/(1.602*10^(-19) C) = E
7,490.6 N/C = E
That is the strength of the electric field.
What statement is not an example of Newton’s first law of motion
Answer:
c
Explanation:
im smart....................... i think
This law is about inertia, and the law displayed in A is Newton's third law of equal and opposite reactions, so option A is correct.
What is Newton’s first law of motion?The basis of classical mechanics is laid out in three assertions known as Newton's laws of motion, which were first articulated by English physicist and mathematician Isaac Newton. These laws describe the relationships between forces acting on a body and its motion.
Unless a force acts on a body that is at rest or moving in a straight line at a constant speed, Newton's first law asserts that it will continue to be at rest or move in that direction.
This law is about inertia (an object wanting to stay in its state of motion) and the law displayed in A is Newton's third law of equal and opposite reactions, therefore, it is not an example of Newton’s first law of motion.
To know more about Newton’s First law of motion:
https://brainly.com/question/974124
#SPJ2
A north magnetic pole is facing another north magnetic pole with a distance x. If the distance between the poles becomes 12x, what happens to the magnitude of the field energy between them?
The answer is "The field energy will increase"
What will happen to the magnitude of the field energy between them is that
The field energy will increaseWhenever there is a stored energy in an object at rest, the object will move in the direction that causes the energy stored to decrease, which will be replaced by movement energy.
Therefore, if two magnets with like poles are pointing together, then the energy stored will decrease as they move apart. Hence, as the distance between poles decreases, field energy increases.
What are magnetic poles?Magnetic pole are region at each end of a magnet where the external magnetic field is strongest.
For more information on magnetic poles, visit
https://brainly.com/question/19542022
Why are models of atoms and molecules useful explain
Answer:
The models are larger versions of atoms/molecules. It is a visualization so we can understand the super small particles.
Explanation:
Atoms and molecules are very, very, small. They average 100 picometers across.
They definitely cannot be seen with the naked human eye. We can only see them with special microscopes (electron, optical, etc). that magnify hundreds of thousands of times.
So, we use models of atoms and molecules. It allows us to study, visualize, understand, and "see" the particles on a much larger scale.
In which part of a lab report would be the following sentence most likely occur? “Since the data showed that the
Answer:
most likely be included in the analysis section of a lab report
Explanation:
In a parallel circuit, if one connection is broken
A. all of the connections stop working. B. B only broken one will stop working
C. Nothing happens to circuit.
Explain:
Can someone help me out please I got it wrong
Answer:
3 maybe since protons=atomic
how much power does it take to do 104 J of work in 8 sec?
Answer:
Given:
W=104J
t=8sec
Solve:
P=?
Equation:
P=W/t or Fd/t
P= 104J'8sec
P=13W
Question 12 of 25
What type of energy is thermal energy?
O A. Chemical energy
O B. Nuclear energy
O C. Kinetic energy
O D. Gravitational potential energy
It’s C kinetic energy
the diameter of the wheels on your car ( including the tires) is 25 inches. you are going to drive 250 miles today. each of your wheels is goingnto turn by an angle of
In the picture shown below A represents a characteristic of only geocentric model, B represents a characteristic common to both geocentric and heliocentric models, C represents a characteristic of only heliocentric model, and D represents a characteristic which the geocentric and heliocentric models do not have.
Under which label will the characteristic, "The sun and planets revolve around a central moon in the solar system" fall?
A
B
C
D
Small household electrical devices, such as vacuum cleaners, televisions, and floor lamps, each draw a different amount of current, but all require 120 volts to operate. Are the outlets in of a power-strip, then, wired in series or parallel
Answer:
the selected configuration is PARALLEL
Explanation:
There are two ways to connect electrical circuits.
In series in this type of circuit the equipment is connected to the same line, in this case the current of the circuit circulates through all the inputs is the same, but the voltage in each one is a part of the total voltage, this circuit has the problem that if an appliance is disconnected or damages the power and the entire circuit is interrupted
V_total = ∑ V_i
In a parallel circuit the equipment is connected in two two cables, for which the current is divided in each branch, the voltage in all the branches is the same, this type of circuit has the advantage that if one equipment is damaged or disconnects the others they can continue working
V_total = V
Therefore, in consequence of the above, the selected configuration is PARALLEL
What happens to Average Speed if distance decreased & time stayed the same?
Answer:
I think you are trying to ask 'what happens to the average speed (of humans or animals.) if the distance decreased and time stayed the same (the time such as what hour it is or what second?)' If that is the case then the average speed will be more since the distance decreased. And the time staying the same might affect it I am not fully sure so I will not say anything about that. I hope this helps!
need help pleaseee !
Answer:
08 and 09 with be 67
Explanation:
i know this because it was the vase major
A 62 kg student, starting from rest, slide down an 10.6 m high water slide. How fast is he going at the bottom of the slide? Use g = 10 m/s2
Answer:
14.6m/s
Explanation:
Given parameters:
Mass of the student = 62kg
Initial velocity = 0m/s
Height of slide = 10.6m
g = 10m/s²
Unknown:
Speed at the bottom of the slide = ?
Solution:
The speed at the bottom of the slide is the final velocity;
v ² = u² + 2gh
v is the final velocity
u is the initial velocity
g is the acceleration due to gravity
h is the height
v² = 0² + 2x 10 x 10.6
v² = 212
v = 14.6m/s
A 2 kg toy car moves at a speed of 5 m/s. If a child applies a 5N force for 2 m in the same direction the car is already moving, what is the change in kinetic energy of the car?
Answer:
[tex]10\: \mathrm{J}[/tex]
Explanation:
The kinetic energy of an object is [tex]KE=\frac{1}{2}mv^2[/tex], where [tex]m[/tex] is the mass of the object and [tex]v[/tex] is the velocity of the object.
The toy car's initial kinetic energy is [tex]KE_{i}=\frac{1}{2}\cdot 2\cdot 5^2=25\: \mathrm{J}[/tex].
After the child applies a 5N force on it in the same direction, its velocity will increase but its mass will stay the same.
To find the final velocity of the toy car, we can use kinematic equation [tex]v_f^2=v_i^2+2a\Delta x, \\ v_f=\sqrt{v_i^2+2a\Delta x}[/tex]
We are given [tex]v_i=5\: \mathrm{m/s}[/tex] and [tex]\Delta x = 2\: \mathrm{m}[/tex].
To find acceleration:
[tex]F=ma, a=\frac{F}{m}=\frac{5}{2}=2.5\: \mathrm{m/s^2}[/tex].
Now substitute [tex]v_i=5\: \mathrm{m/s}, \: a=2\: \mathrm{m/s^2}, \: \Delta x = 2\: \mathrm{m}[/tex] into [tex]v_f=\sqrt{v_i^2+2a\Delta x}[/tex] to get [tex]v_f\approx 5.92\: \mathrm{m/s}[/tex].
Using this, we can find the final kinetic energy of the toy car is [tex]KE_f=\frac{1}{2}\cdot 2\cdot 5.92^2[/tex].
Thus, the change in kinetic energy is [tex]KE_f-KE_i=\frac{1}{2}\cdot2\cdot 5.92^2-\frac{1}{2}\cdot 2\cdot 5^2=\fbox{$10\: \mathrm{J}$}[/tex] (one significant figure).
The change in the kinetic energy of the car is 10 J.
The given parameters;
mass of the car, m = 2 kginitial velocity of the car, u = 5 m/sforce applied by the child, F = 5 Ndistance traveled, s = 2 mThe acceleration of the car is calculated as follows;
[tex]F = ma\\\\a = \frac{F}{m} \\\\a = \frac{5}{2} \\\\a = 2.5 \ m/s^2[/tex]
The final velocity of the car is calculated as follows;
[tex]v^2 = u^2 + 2as\\\\v = \sqrt{u^2 + 2as} \\\\v = \sqrt{5^2 \ + \ 2(2.5)(2)} \\\\v = 5.92 \ m/s[/tex]
The change in the kinetic energy of the car is calculated as follows;
[tex]\Delta K.E = \frac{1}{2} m(v^2 - u^2)\\\\\Delta K.E = \frac{1}{2} \times 2 \times (5.92^2\ - \ 5^2)\\\\\Delta K.E = 10 \ J[/tex]
Learn more about kinetic energy here: https://brainly.com/question/1932411
Kiara starts at 4, walks 6 blocks left and 2 blocks right. What is her displacement?
Which term describes the relatively constant internal conditions of an organism?
Single Cellular
Uniformity
Homeostasis
Organ System
Answer:
The correct answer is C. Homeostasis
Explanation:
Homeostasis describes the relatively constant internal physical conditions of an organism.
Some giant ocean waves have a wavelength of 25 m and travel at 6.5 m/s with a frequency of 0.26 HZ. What is the period of such a wave ?
Answer:
3.85s
Explanation:
Given parameters:
Wavelength = 25m
Velocity = 6.5m/s
Frequency = 0.26Hz
Unknown:
Period of the wave = ?
Solution:
The period of a wave is the inverse of the frequency of the wave.
Period = [tex]\frac{1}{frequency}[/tex]
Period = [tex]\frac{1}{0.26}[/tex] = 3.85s
A block of mass m = 4.4 kg slides from left to right across a frictionless surface with a speed 9.2 m/s It collides in a perfectly elastic collision with a second block of mass M that is at rest. After the collision, the 4.4-kg block reverses direction, and its new speed is 2.5 m/s The block of mass M travels to the right at a speed V of 6.7 m/s what is M
Answer:
[tex]m_2=6.3\:\mathrm{kg}[/tex]
Explanation:
In a perfectly elastic collision, the total kinetic energy of the system is maintained. Therefore, we can set up the following equation:
[tex]\frac{1}{2}m_1{v_1}^2+\frac{1}{2}m_2{v_2}^2=\frac{1}{2}m_1{v_{1'}}^2+\frac{1}{2}m_2{v_{2'}}^2[/tex]
Since the second block was initially at rest, [tex]\frac{1}{2}m_2{v_2}^2=0[/tex].
Plugging in all given values, we have:
[tex]\frac{1}{2}m_1{v_1}^2=\frac{1}{2}m_1{v_{1'}}^2+\frac{1}{2}m_2{v_{2'}}^2,\\\\\frac{1}{2}\cdot4.4\cdot9.2^2=\frac{1}{2}\cdot 4.4 \cdot (-2.5)^2+\frac{1}{2}\cdot m_2\cdot 6.7^2,\\m_2=\fbox{$6.3\:\mathrm{kg}$}[/tex].
When measuring wellness you must consider
A all components of health
B your physical fitness being in the top 10% of the population
C being free of diseases
D both physical and mental health
Answer:
The answer is A) all components of health
Explanation:
Got it right on edge
an incline projection can achive maximium horizontal horizontal range at an angle of projection,ፀ=45 why?
Answer:
Explanation:
For an incline projection made at angle of θ , expression of horizontal range R can be given by the following equation .
R = u² sin 2θ / g
u is initial velocity of throw .
For range R to be maximum , the value of sin 2θ must be maximum . The maximum value of sin of an angle is 1 , so
For maximum R ,
sin2θ = 1 = sin90
2θ = 90 .
θ = 45⁰ .
So for projection made at 45⁰ , horizontal range is maximum .
A safety plug is designed to melt when the pressure inside a metal tank becomes too high. A gas
at 51.0 atm and a temperature of 23.0°C is contained in the tank, but the plug melts when the
pressure reaches 75.0 atm. What temperature did the gas reach?
A volcano erupts spewing ash into the air and sending lava flowing down the side of the mountain. Looking at the image explain how the eruption of the volcano involves each of the Earth’s four spheres
Answer:
A lateral eruptions or lateral blast is a volcanic eruption which is directed laterally from a volcano rather than upwards from the summit. Lateral eruptions are caused by the outward expansion of flanks due to rising magma. Breaking occurs at the flanks of volcanoes making it easier for magma to flow outward.
Explanation:
How does the geosphere interact with the biosphere during a fire?
Answer: A forest fire could affect the geosphere by ash and the heat from the fire, but the fire would affect the biosphere by less oxygen in the air and would make it hard for human to breath affecting climate change. Also many homes to wildlife that live in the forest would lose their homes. This would result in lose of money from no hunting and that affect the economy.