Engineering

In a parking garage, each level is 18 feet apart, Each ramp to a level is 120 feet long. Find the measurement of elevation for each ramp?
1 Answer
Please answer this asap
2 Answers
Explain what the engineering team should advise in the following scenario.Situation: An engineering team is analyzing a problem with a dam near a large metropolitan area. The dam reservoir has a capacity of 300 billion cubic feet, and it produces hydroelectric power for local municipalities. The dam has developed a severe crack.
1 Answer
Three spheres are subjected to a hydraulic stress. The pressure on spheres 1 and 2 is the same, and they are made of the same material. The fractional compression on the third sphere is equal to the fractional compression on the first sphere times the reciprocal of the fractional compression on the second. If the pressure on the third sphere is 150000 N/m2 , what is the Bulk Modulus for the third sphere
1 Answer
can someone please help me with this I've an exams tomorrow
1 Answer
15 POINTS! Help.What might happen if a systems engineer overlooked a detail that may have been discovered by a manufacturing engineer? Explain using an example.
2 Answers
Fig_Q56. A steel rod is stressed by a tension force of 250 N. It is found that the rod has length of 45m and diameter of 1.5 mm. If the modulus of elasticity of the steel rod is assumed as 2 x 105MPa, determine the strain of the steel rod due to the applied force.
1 Answer
state the parallelogram law of forces
2 Answers
Giving away points hope they help with your questions
1 Answer
g Design of a spindle present in an existing design needs to be reviewed for use under new loading needs. It is currently designed to withstand combined torsional and compressive loading. The design team needs to determine what the maximum torque it can withstand before failing if a compressive, axial load of 15 kips is present. The ultimate compressive and tensile strengths of the material are 135 ksi and 40 ksi, respectively. Determine the torsional shear stress that will just cause failure using a non-conservative failure theory.
1 Answer
Knowing that the central portion of the link BD has a uniform cross-sectional area of 800 2, determine the magnitude of the load P for which the normal stress in that portion of BD is 50 .
1 Answer
Which type of pictorial drawing is easier to draw on the job site?ObliqueIsometricorthographic
2 Answers
The distribution of SAT scores of all college-bound seniors taking the SAT in 2014 was approximately normal with mean =1497 and standard deviation =322. A certain test-retake preparation course is designed for students whose SAT scores are in the lower 25%, percent of those who take the test in a given year. What is the maximum SAT score in 2014 that meets the course requirements?
2 Answers
How may the desire for a perfect lawn be related to environmental pollution? A. Lawns have little to do with environmental pollution. B. Perfect lawns require excess use of manual labor. C. Manicured lawns are subject to increased runoff. D. Lawns absorb pesticides and fertilizers and these chemicals leach out of the lawn and run into creeks, streams and eventually, rivers, with rain or watering, eventually reaching the ocean.
1 Answer
Refrigerant 134a enters the evaporator of a refrigeration system operating at steady state at -16oC and a quality of 20% at a velocity of 5 m/s. At the exit, the refrigerant is a saturated vapor at -16oC. The evaporator flow channel has constant diameter of 1.7 cm. Determine the mass flow rate of the refrigerant, in kg/s, and the velocity at the exit, in m/s.
1 Answer
FDR is regarded as one of our greatest presidents but he made some real errors, what were they? Why? Is it fair to blame him for these considering the magnitude of what he faced?
1 Answer
In the production of soybean oil, dried and flaked soybeans are brought in contact with a solvent (often hexane) that extracts the oil and leaves behind the residual solids and a small amount of oil. a. Draw flow diagram of the process, labeling the two feed streams (beans and solvent) and the leaving streams (solids and extract). b. The soybeans contain 18.5 wt% oil and the remainder insoluble solids, and the hexane is fed at a rate corresponding to 2.0 kg hexane per kg beans. The residual solids leaving the extraction unit contain 35.0 wt% hexane, all of the non-oil solids that entered with beans, and 1.0% of the oil that entered the beans. For a feed rate of 1000 kg/h of dried flaked soybeans, calculate mass flow rates of extract and residual solids and the composition of extract.
1 Answer
Depending on the economy, financial institution, and your credit history, interest rates commonly range from
2 Answers
You are developing a mind map for measuring the viscosity of fluid. At which stage in the process will you specify the equipment needed for the experiment?Connecting the subtopics fo the central ideaDefining the lower-level subtopicsCreating the imageDefining the subtopics
2 Answers
please help i am give brainliest i really need help guys no links please ??? can someone create a 2-minute presentation about wind also i am giving 50 points no dam links if you put links i will hack your brainiy account
1 Answer
I need help with this, question thank you so much
2 Answers
Identify parts of the E-Cig that constitute voltage, current, and resistance. Discuss the role each plays in the E-Cig and typical values for each including units.Discuss the electrical dangers of an E-Cig. Give specific examples. There are many electrical safety rules. Pick one, and discuss its application on a small system, such as the E-Cig.
1 Answer
Barries of effective communication?
1 Answer
For some metal alloy, a true stress of 345 MPa (50040 psi) produces a plastic true strain of 0.02. How much will a specimen of this material elongate when a true stress of 412 MPa (59760 psi) is applied if the original length is 480 mm (18.90 in.)? Assume a value of 0.22 for the strain-hardening exponent, n.
1 Answer