PLS HELP ASAP PLSSSS

The option that can lead to deviations from Beer's law at constant path length is option A.

Using monochromatic radiation All radiation that was not absorbed by his sample when stray light reaches the detector is transmitted to the detector.

All of the above factors can lead to deviations from Beer's Law if the path length is constant. Optical pathlength refers to the distance that light travels through a sample and is usually kept constant in spectrophotometric experiments in order to accurately measure the sample's absorbance.

Therefore, unless monochromatic radiation is used, the absorbance of the sample may not accurately reflect the concentration of the solute, as different wavelengths of light may be absorbed differently.

For more information on Beer's Law kindly visit to

https://brainly.com/question/18591932

#SPJ4

Given that 1 kWh = 3. 6 MJ and that 1 Btu = 1055 J, It is shown that 1 kWh = 3412 Btu.

1 kilowatt (kWh) = 3.6 mega Joules (MJ)

1 British thermal unit (Btu) = 1055 Joules (J)

As we know that:

1 MJ = 1000000 J

Since

1 kWh = 3.6 x 1000000 J

Calculate for 1 J

1 J = 1 ÷ 1055 Btu

1 kWh = 3.6 x 1000000 x (1 ÷ 1055) Btu

1 kWh  = 3412.32 Btu

So it is calculated that 1 kilowatt (kWh) is equal to 3412 British thermal units (Btu).

You can also learn about British thermal unit (Btu) from the following question:

https://brainly.com/question/19431525

#SPJ4

Moving down the concentration gradient means that materials move from an area of high concentration of the material to an area of low concentration of the material.

In chemistry, concentration is the amount of a substance in a given space. Another way to describe concentration is the proportion of the solute to a solvent or entire solution. In general, mass/unit volume is used to express concentration. Instead of using volume, concentration can be stated as a mass per unit. Although concentration is typically used to describe chemical solutions, it may be computed for any mixture.

This can be seen in osmosis, where water moves from a higher concentration of solute to a lower concentration of solute.

To learn more about concentration

https://brainly.com/question/26255204

#SPJ4

The rate constant of the reaction is 0.56 M⁻¹s⁻¹. The time required to change the concentration of the reactant from 0.900 to 0.100 M is 15.87s.

The half-life of a reaction can be defined as the time needed for a reactant to reach one-half of its initial concentration. For a 1st-order reaction, the half-life is independent of concentration and constant with time.

The half-life period of the second-order reaction can be written as:

[tex]\displaystyle t_{1/2} =\frac{1}{k[A]_o}[/tex]

Given the half-life of the reaction = 2.00 s

The initial concentration of [NOBr]₀ = 0.900 M

The rate constant of the reaction, k = 1/2 ×0.900 = 0.56 M⁻¹s⁻¹

The time required to change concentration from 0.900 to 0.100 M is:

[tex]\displaystyle kt =\frac{1}{[A]} -\frac{1}{[A]_o}[/tex]

0.56 ×t = 1/0.1 -1/0.9

t = 15.87 s

Learn more about half-life period, here:

https://brainly.com/question/1851154

#SPJ1

Lithium has a valence of 1, so it will not usually reach an octet in a bond. It tends to form ionic bonds, in which there is only one electron transfer, rather than two or more which would be required to reach an octet.

Lithium is a soft, silver-white metal that is the lightest of all alkali metals. It is a key component in many batteries, and is also used in a variety of other applications. It has a low reactivity, and is relatively stable when exposed to air and water. In its elemental form, Lithium is a highly flammable, corrosive metal that is rarely found in its pure form in nature. It can be found in minerals such as lepidolite and spodumene, and is commonly mined from salt flats and brine pools.

To learn more about Lithium
https://brainly.com/question/15178590
#SPJ4

Answer:

Explanation:

Pb(OH)2 + 2NaOH → Pb(OH)2 + 2NaOH

The balanced equation would be PbO + 2NaOH → Pb(OH)2 + Na2O

The reactant PbO is a lead oxide which is an acidic oxide, it reacts with NaOH, a strong base, to form Pb(OH)2, a lead hydroxide, which is a salt of lead, and Na2O which is sodium oxide , a base.

We can use the distance when the meter stick fell before you caught it to figure out your reaction time.  

Meterstick is either a straightedge or foldable ruler which is used to measure a  length, and is especially common in the construction industry. They are often made up of wood or plastic, and often have metal or plastic joints so that they can be folded together. Metersticks are usually divided with lines for each millimeter (1000 per meter) and numerical markings as per centimeter (100 per meter), with the numbers or either in centi- or millimeter.

Formula is the basis: d = 1/2 gt2. In this formula, “d” is equals to the distance the object fell, “g” equals to gravitational acceleration (9.8 m/s2), and “t” is the time the object was falling.

To know more about meterstick here

https://brainly.com/question/29690562

#SPJ4

The property of the covalent compound that is influenced by ionic character is boiling point. Option B

We know that for compounds, the kind of bonds that they have are usually neither here nor there. The bonds would have an ionic character and also a given amount of the covalent character.

We must note that the ionic character of a bond is very important when we discuss intermolecular interactions and they do affect the boiling points of the substances very much.

Learn more about boiling point:https://brainly.com/question/2153588

#SPJ1

Answer:

A-Ideas

Explanation:

The total random kinetic energy of all the molecules in one mole of hydrogen at a temperature of 300k is 3741.3 J.

Given temperature (T) = 300K

The number of moles of hydrogen given are (n) = 1

Molecular weight of hydrogen (M) = 1g

Let the kinetic energy = KE

We know that Kinetic Energy (KE) = 1.5nRT where R = Rydbergs constant

So, KE (total) = 1.5nRT,

the total random kinetic energy is KE = (1.5) x (1) x (8.314) x (300) = 3741.3J/mol

The energy of motion is known as kinetic energy, and it can be observed in the motion of objects or subatomic particles. Examples of kinetic energy in action include a person walking, a baseball soaring through the air, a piece of food falling from a table, and a charged particle in an electric field.

To learn more about hydrogen click here https://brainly.com/question/11837837

#SPJ4

Ice will not melt as we need 16.72 KJ of heat but we have only 3.76 KJ

In thermodynamics, the enthalpy of fusion can be described as the change in its enthalpy resulting from giving energy, heat, to a specific amount to change its state from a solid to a liquid.

Given the reaction is  2 Na (s) + 2 H₂O(l) → 2 NaOH (aq) + H₂ (g)

Given the mass of sodium = 0.470 g

The moles of sodium = 0.470/23 = 0.020 mol

Given that two moles of sodium (Na) release heat = 368 KJ

Heat released by 0.020 mol of sodium (Na) = (368/2) × 0.020 = 3.76 KJ

Given the mass of ice = 50g

The number of moles = 50/18 = 2.78 mol

For melting, one mole of ice heat is required = 6.02 kJ/mol.

For 2.77 mol of ice = 6.02 × 2.78 = 16.72 KJ

But we have only 3.76 KJ of heat therefore, the ice will not melt.

Learn more about enthalpy of fusion, here:

https://brainly.com/question/20897184

#SPJ1

Answer:

There are 8.30x104-24 atoms of oxygen in 2.50 mol of oxygen gas. There are 7.53x10*23 atoms of oxygen in 2.50 mol of oxygen gas.

When molecules move faster, they increase their kinetic energy.

What is Kinetic energy?

Kinetic energy is essentially the energy of motion. It is the type of energy that an object possesses as a result of its motion. It is commonly defined as the work required to accelerate a given mass body from rest to its stated velocity. Kinetic energy is directly related to the object's mass and the square of its velocity.

This increase in kinetic energy causes the molecules to vibrate more rapidly, resulting in an increase in temperature. As molecules move faster, they also collide with each other more frequently, leading to more chemical reactions.

To know more about kinetic energy,

https://brainly.com/question/8101588

#SPJ4

1.08 moles of water () produced by the reaction of 0.90mol of oxygen.

Explanation:

Moles of oxygen given = 0.90 mole

Moles of water are to be calculated.

Step 1 : Write the chemical reaction and balance it.

5 mole of  reacts with 4 mole of  to give 4 moles of NO and 6 moles of .

Step 2 : Calculate moles of water () utilising  mole ratio.

The coefficient of  is 6 and coefficient of  is 5, So mole ratio of  to  is 6 : 5

Moles of  = 0.90 × 6 (moles of ) ÷ 5 (moles of )

Moles of  = 1.08 moles

1.08 moles of  is produced by the reaction of 0.90 mole oxygen ()

For more information on moles visit: https://brainly.com/question/26416088

#SPJ4

A tiny amount of weak hydrochloric acid is mixed with a quantity of marble chips (CaCO3), to decrease the rate of reaction we do decreasing the surface area of the marble chips, decreasing conc. HCL and many more.

Several ways are:-

1. Decreasing the surface area of the marble chips: By breaking the marble chips into smaller pieces, the surface area that is available for the acid to react with is reduced, slowing down the reaction.

2. Decreasing the concentration of the hydrochloric acid: By using a less concentrated solution of hydrochloric acid, the number of acid molecules available to react with the marble chips is reduced, slowing down the reaction.

3. Increasing the temperature: By performing the reaction at a lower temperature, the kinetic energy of the acid and marble chip molecules is reduced, slowing down the rate of collision between them, which slows down the reaction.

4. Using a catalyst: Addition of a catalyst to the reaction can change the reaction mechanism and decrease the activation energy needed for the reaction to occur, thus slowing down the reaction.

5. Using an inhibitor: An inhibitor is a substance that slows down the reaction by binding to the enzyme or catalytic site and preventing the substrate from binding.

It's important to note that these methods may also affect the overall yield of the reaction, so it's essential to use the appropriate method(s) for the specific experiment and goals.

To know more about hydrochloric acid please refer: https://brainly.com/question/14006357

#SPJ4

Pyruvate is converted to lactate in anaerobic conditions by anaerobic glycolysis. During anaerobic respiration, two ATP molecules are produced.

What is the primary step in glycolysis?

The method by which glucose is metabolized to produce energy is known as glycolysis. It generates water, ATP, NADH, and two pyruvate molecules. It doesn't need oxygen to happen because it happens in a cell's cytoplasm. Both in aerobic and anaerobic organisms, it happens.

How is glycolysis referred to?

Gustav Embden, Otto Meyerhof, & Jakub Karol Parnas identified the Embden-Meyerhof-Parnas (EMP) pathway, which is the most typical kind of glycolysis. The Entner-Doudoroff pathway and several heterofermentative & homofermentative pathways are examples of additional pathways that are included in the term "glycolysis."

To know more about glycolysis visit:

https://brainly.com/question/14076989

#SPJ4

In anaerobic circumstances, anaerobic glycolysis converts pyruvate to lactate. Two ATP molecules are created during anaerobic respiration.

The process of converting glucose into energy is known as glycolysis. Water, ATP, NADH, and two pyruvate molecules are produced. It does not require oxygen to occur since it occurs in the cytoplasm of a cell. It occurs in both aerobic and anaerobic species.

The Embden-Meyerhof-Parnas (EMP) route, which is the most common kind of glycolysis, was discovered by Gustav Embden, Otto Meyerhof, and Jakub Karol Parnas. Additional processes included in the word "glycolysis" include the Entner-Doudoroff pathway and numerous heterofermentative and homofermentative pathways.

Here,

Anaerobic glycolysis converts pyruvate to lactate under anaerobic conditions. During anaerobic respiration, two ATP molecules are produced.

To learn more about glycolysis, go to:

brainly.com/question/14076989

#SPJ4

a) The mole ratio is 2/1

b) The mole ratio is 4/6

c) The mole ratio is 2/3

We have to note that the mole ratio is the ratio of the stoichiometric coefficient that we have between two reactants that can be found in an equation. In the case of the reaction equations that we have, we must look closely at each equation.

As we can see, each of the reaction equations is balanced and we can now be able to obtain the mole ratio of each of the reaction as shown in the answer above.

Learn more about mole ratio:https://brainly.com/question/15288923

#SPJ1

Answer:

186.25

Explanation:

KCL= 74.5 (molar mass)

2.5*74.5= 186.25

Entropy and the inefficiency of energy transfer are part of the Second Law of Thermodynamics.

The first law of thermodynamics states that neither creation nor destruction of energy is possible. The universe becomes more entropic when a spontaneous process occurs, according to the second law of thermodynamics. Thermodynamics' third law: The entropy of a perfect crystal is 0 at absolute zero Kelvin. The overall entropy of a system may only ever increase or stay constant during spontaneous processes, according to the second law of thermodynamics. If the physical process is irreversible, the overall entropy of the system and its surroundings must increase. For a process to be irreversible, the final entropy needs to be higher than the starting entropy: Sf > Si (irreversible process). The overall entropy of a system and its surroundings can remain constant when a system is in thermodynamic equilibrium or undergoing a reversible process. The second law is sometimes known as the Law of Increased Entropy.

To learn more about entropy click here https://brainly.com/question/24278877

#SPJ4

A 7.5 10-3 M Ba(OH)2 solutions at 25°C has a pH of 1.82. (option b).

A homogenous solution of two or more ingredients with particles smaller than one nm is referred to as a solution. Solutions come in many forms, such as soda water, salt and sugar solutions, etc. In a solution, every element appears as a single phase.

In chemistry, a solution is a homogeneous mix of two or more molecules in relative proportions that can be constantly changed up to what is known as the limit of solubility. Although the term "solution" is frequently used to refer to the liquid state of matter, solutions of gases and solids are also possible.

To know more about Solution visit:

https://brainly.com/question/1616939

#SPJ4

The planes of cleavage that the mineral have is 1 as the mineral name is Muscovite mica.

The crystal lattice structure of a mineral affects its propensity to split or break along flat planar faces, or cleavage. These 2D surfaces, also known as cleavage planes, are produced by the alignment of atoms in the crystal structure or lattice through relatively weak connections.

The mineral depicted in the image is called "Muscovite mica," and it has layers that seem like flat sheets. Muscovite mica is far more likely to break along the layers because it only has weakly bonded potassium ions. There is just one ideal cleavage plane as a result. This cleavage is evident in the capacity to peel mica sheets.

Learn more about cleavage

brainly.com/question/10924382

#SPJ4

The conclusion is supported by these results is binding of oxygen to the protein changes the protein's tertiary structure to a conformation that resists the effects of urea.

Fluorescence is a property that some chemicals have that allows them to emit visible light after absorbing radiation that is typically invisible, like ultraviolet light.

Fluorescence is the name given to the process of electromagnetic radiation typically visible light emitting from a material as a result of atoms being excited. These excited atoms almost immediately (within 10⁻⁸ seconds) begin emitting again. In most cases, the initial excitation is brought on by the energy absorption of incident radiation or particles, like X-rays or electrons.

To know more about fluorescence visit:

https://brainly.com/question/24228588

#SPJ4

Measuring tools like Clear ruler, yardstick, measuring tape etc. They are very useful for the perfect fit and shape of any garment and even home furnishing.  

Sewing is the craft of fastening or attaching objects using stitches which is made up of a sewing needle and thread.

Measuring tools are the instruments used by practitioners and researches to aid in the assessment or evaluation of the subjects, clients or patients etc. These instruments are used to measure or collect the data on a variety of variables ranging from psychosocial wellbeing or physical functioning.

Measuring tools in sewing are as follows: Measuring tape, clear ruler, quilting ruler, yardstick, French curve etc.

To know more about sewing here

https://brainly.com/question/1642881

#SPJ4

A proposed explanation for an observation is theory. Option C is the correct answer.

This refers to a carefully articulated explanation for observations of the natural world that have been arranged using the scientific method, gathering many facts and hypotheses.

A proposed explanation for an observation is a statement or theory that attempts to explain or account for an observation. It is a possible explanation for a phenomenon and is often based on available evidence, research, and data. It may be tested and refined through further observation and experimentation to determine its accuracy and validity.

Learn more about theory on

https://brainly.com/question/29457011

#SPJ1

The mole fraction of ethanol, C2H5OH is 0.076 that can be calculated by using the density of water.

The mole fraction of any solution is described because the ratio of the quantity of moles of that is present withinside the technique to the entire quantity of moles of all of the additives of the solution. Molarity on the other hand is the ratio of moles to the volume.

Molecular mass of ethanol = 46g

The molarity of the solution is 4.6 molal=4 moles in 1L solution

Molecular mass of water =18g

Density of water = 1kg/m3 = 1000g/L

So, mass of water in 1 l solution = 1000g

So moles = 1000/18 = 55.55 moles

Thus, mole fraction of ethanol= 4.6/(4.6+55.6) =0.076

To learn more about mole fraction check the link below:

https://brainly.com/question/1601411

#SPJ4

The unit of f''(a) is milliliters/minute^2

The function t=f(a) models the time, in minutes, for a chemical reaction to occur as a function of the amount a of catalyst used, measured in milliliters.

So, here double differentiation is to be done.

t=f(a)

differentiating with respect to t,

d(t)/dt = d(f'(a))/dt

or, d(f'(a))/dt = 1

again differentiating with respect to t,

d [d(f'(a))/dt]/dt = d(1)/dt = 0 ...1

or, f''(a) = 0

so, here if we put 'unit expression' in Left hand side of 1

it is d [d(f'(a))/dt]/dt  i.e.  mililiters/miniute/minute [as given t is measured in minute and f(a) is measured in ml)

or, ml/minute^2

so as we are performing double differentiation, the unit of f''(a) is milliliters/minute^2

To know more about unit calculation here:

https://brainly.com/question/28773672#

#SPJ4

The periodic repetition of properties of elements is due to the regular arrangement of electrons in the atoms of those elements. This regular arrangement is known as the "periodic table" of elements. This is due to the behavior of electrons in atoms and the increasing number of valence electrons as atomic number increases, resulting in a regular pattern of electron configurations and properties.

Elements are arranged in the periodic table according to increasing atomic number. Elements in the same vertical row (group) have similar chemical and physical properties, and elements in the same horizontal row (period) have similar electronic configurations of their atoms.

The reason for this repeating periodic property is the behavior of the electrons in the atoms. As the atomic number increases, the number of protons in the nucleus increases, and the number of electrons in the atom increases. These electrons occupy different energy levels or shells around the atomic nucleus. The outermost shell electrons, the so-called valence electrons, are responsible for the chemical behavior of atoms and participate in chemical bonds. As the atomic number increases, the number of valence electrons in the atom increases. This results in a regular pattern of electron configurations and thus a regular pattern of properties.

Learn more about periodic repetition here:https://brainly.com/question/1917984

#SPJ4

Answer: We can calculate the energy levels of an atom

Explanation:

Spectral lines tell us how many different energy levels an atom has, and how far apart those energy levels are spaced.This is possible because spectral lines are the result of an excess (emission lines) or deficiency (absorption lines) of observed photons emitted from certain types of matter. The lines are caused by electrons moving between energy levels within individual atoms. Since each element emits it's own unique spectrum, this means that different types of atoms must have a distinct number of electrons in very particular energy levels.